Log:
Trier : Nom ↑   Téléchargements   Évaluation   Taille ↑  
Téléchargements : 4   Taille : 240 kb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name

Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DEI DEALER. ALL UNITS RECEIVED BY DEI FOR WARRANTY REPAIR WITHOUT PROOF OF DEI DEALER INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY. Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. BY PURCHASING THIS PRODUCT, THE CONSU

Téléchargements : 7   Taille : 205 kb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name

Directed Electronics has been the industry leader in high-quality automotive security and audio equipment since 1990, and with the introduction of the Directed Studio line of high-quality loudspeakers for the automobile, Directed continues to set new standards of performance, reliability, and affordability in the mobile electronics industry. Featuring injection-molded fiberglass reinforced baskets with graphite injected cones and neodymium motors, the Directed Studio line of automotive speakers

Téléchargements : 0   Taille : 628 kb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name

Thermal protection is also indicated by the green LED shutting off. 5 © 1999 Directed Electronics, Inc SPEAKER WIRING DIAGRAMS Stereo operation Mono operation For bridged two channel operation as shown in this diagram, connect right channel RCA cables to the “Front” inputs of the amplifier, and left channel RCA cables to the “Rear” inputs of the amplifier. For summed subwoofer applications, connect RCA cables per the input jack marking. Simultaneous stereo/mono operation (two channel shown) © 19

Téléchargements : 0   Taille : 1 mb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name@name@name@name@name@name

Figure 7Figura 7Abbildung 7HGFIEDABC CO552 CO652 Dimensions inches/mm, Dimensions pouces/mm, Dimensiones plg./mm, Abmessungen Zoll/mm, Dimensioni pollici/millimetri, Dimensoes polegadas/mm A 1.97/50 2.36/60 B 0.71/18 0.91/23 C 2.76/70 3.15/80 D 4.72/120 5.63/143 E 5.12/130 6.50/165 FRANCAIS OU MONTER LES HAUT-PARLEURS Le choix du bon emplacement des haut-parleurs aura un effet majeur sur la qualite du son du systeme. Plusieurs choses doivent etre prises en consideration pour faire le meilleur ch

Téléchargements : 0   Taille : 1 mb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name@name@name@name@name@name

Different considerations are needed when choosing the locations that best suit your needs. The locations must be large enough for the speakers to fit. Care is needed to ensure that the location you have chosen will not affect any of the mechanical or electrical operations of the vehicle. Determining the best location for the speakers will depend on your cosmetic needs and your vehicle's interior. If minimal intrusion in your vehicle is desired, factory speaker locations may be the ticket for you

Téléchargements : 5   Taille : 240 kb   Fabricant : Atrend Enclosures  
Catégorie : Haut-parleurs et caissons de basse
@name

(Refer to the trim ring information at the end of this section.) © 2003 Directed Electronics, Inc Tweeter Surface Mounting 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. 2. Place the surface mount housing against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is the mounting screw hole. 4. Drill the larger off-center hole using a 3/8" drill bi





catégories