Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Features •When attached to a camcorder this unit functions as a video light and flash. •Can only be used with a camcorder that has the intelligent accessory shoe attached. •Video light ON/OFF/AUTO is controlled from the Standby mode. When set to AUTO the video light comes on automatically in dark places. •The video flash can only be used on a camcorder with the PHOTO recording function. As the brightness of the flash is automatically adjusted according to the distance of the subjects, your picture does not become whitish with too much brightness. Precautions Be careful not to touch the lighting section, because the plastic window and surrounding surfaces are hot while the light is on and just after it is turned off. •Never look directly at the bulb while the video light or flash is on. •Avoid placing the video flash light near combustible or volatile solvents such as alcohol or benzine. •Do not let any solid object or liquid fall onto or into the video flash light. •Do not knock or jolt the video flash light while it is turned on as it may damage or shorten the life of the bulb. •Do not leave the video light on while it is resting on or against something; it may cause a fire or damage the video flash light. •While using the video flash light, the battery supplies power to both the camcorder and the video flash light. This shortens the operating time of the battery to less than half of the normal time. •Do not pick up the camcorder by the head of the video flash light. • Remove the video flash light before putting the camera into a carrying case. • Do not place anything over the ventilation grill. • When the cover is hot do not allow it to get wet. On cleaning Clean the video light with a dry soft cloth. You can remove stubborn stains with a cloth lightly dampened with a mild detergent solution, then dry the unit with a soft cloth. Never use strong solvents, such as thinner or benzine, since these will damage the finish on the surface. 3 Keep pressing the camcorder PHOTO button lightly until a picture appears. The video flash light flashes, and the still picture appears in the viewfinder. To change the still picture, release the camcorder PHOTO button. The video flash light starts charging after you release the camcorder PHOTO button. Be sure you have the battery charge complete mark in the viewfinder (or display) before you press the camcorder PHOTO button again. The camcorder will adjust brightness after you press the camcorder PHOTO button, so that the picture may be darkened temporarily before the video flash light flashes. 4 Press the camcorder PHOTO button deeper. The seven dots disappear, and then the recording will be completed. After the still picture is recorded, the video flash light starts recharging. Notes •The appropriate distance between a subject and the video light is about 1 m to 4 m in a dark room. •During recording, keep your fingers away from the sensor a of this unit. Otherwise, the brightness of the flash cannot be adjusted properly. •Set the video flash power switch to OFF after use. •When using the flash in rapid succession, the circuit protector may intervene, and disable the unit. If this happens turn the unit’s power switch to OFF and wait 5-10 minutes before using again. •The video flash light will need to recharge even if it is completely charged after: - you set the power switch to OFF. - you set the camcorder standby switch to other positions, LOCK or STANDBY. C Using the video light To use the video light automatically 1 Set the power switch to AUTO. 2 Set the camcorder to standby mode. The video light turns on automatically when using the camcorder in a dark place. The video light turns off automatically after approx. 5 minutes pass in the standby mode. To turn off the video light when in use, cancel the standby mode. To control the video light with the camcorder in standby mode 1 Set the power switch to ON. 2 Set the camcorder to standby mode. The video light is turned on in sync with the camcorder. To turn off the video light, cancel the standby mode of the camcorder or set the power switch to OFF. After use Set the power switch to OFF. Notes •The battery discharges while the camcorder is in standby mode. Cancel standby mode when not in use. •Store in pouch when not in use. •Make sure the video light has cooled down before storing it. D Lighting up a subject •When recording indoors with this unit, you can get clear and beautiful color pictures. •For wide angle shots, the video light may not light the corners of pictures completely. Use the video light for shooting the main subject of the picture effec...