Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
c. Place a large cup underneath the steam nozzle and turn the SW dial to the hot water position (fig. 2c). Fill with 3 to 4 oz. of hot water. This cleans the nozzle. d. Immerse the four frothXpress parts in the cup with hot water. This will force out any milk. Assemble when you need it again. Make sure that the small "o-ring" in the knob is clean and seated properly (fig. 15). When cleaning the milk container please make sure that the seal and the straw are inserted properly into the milk container lid (fig. 3e). Otherwise the system cannot syphon milk properly. 13. 9. Automatic Monitoring Controls The C1500 has automatic monitoring controls. The display will show when cleaning, refilling and any other maintenance is necessary. Here are the messages: PLEASE WAIT / HEATING UP The C1500 is heating up. Wait until a different message appears. RINSE MACHINE / PRESS BUTTON You must push the BUTTON. Hot water pumps through the coffee spouts and stops by itself. During this procedure the display shows RINSING. HOT WATER CYCLE NECESSARY Place a cup underneath the nozzle and turn the SW Dial to the hot water position (fig. 2c). When the cycle stops, turn the SW Dial back to the 0-position (fig. 2a). SET STEAM/WATER / DIAL TO ZERO The SW Dial is either in the steam position (fig. 2b) or in the hot water position (fig. 2c). Turn the SW Dial to the 0-position (fig. 2a) and the message will go away. HEATING UP The ThermoBlock is heating for steaming. Wait until the display reads STEAM READY / PRESS BUTTON (see chapter 8.3). TRAY MISSING The tray is missing or not inserted properly. TABLET CLEANING This message will alternate with the regular message. See chapter 12.1. DECALCIFYING NECESSARY This message will alternate with the regular message. See chapters 12.2 and 12.3. EMPTY TRAY The tray needs to be removed and the contents emptied. As long as this message appears all other functions are blocked. See chapter 9.1. FILL / WATER TANK There is not enough water in the water tank or the water tank is completely empty. As long as this message appears all other functions are blocked. CHANGE FILTER It is time to replace the Claris Filter Cartridge. See chapters 11 through 11.2. 9.1 Empty Tray When the display reads EMPTY TRAY all other functions are blocked. Move the coffee spout up and carefully lift up the tray and pull it out (fig. 16). The tray has a total of four parts (fig. 1a). • Remove the Used Coffee Container and empty it. This container holds between 10 and 16 coffee portions, depending how large the used coffee portions are. • Discard the water in the tray. This water is the result of the ThermoBlock system: after each brew cycle it forces the remaining water into the tray. This way you never have any stale water inside the heating system. Clean all parts and assemble. Important: Make sure that the used coffee container is placed onto the supporting tray before inserting the complete tray back into the machine. Otherwise, used coffee will fall into the tray causing an overflow. 14. 10. Changing Parameters Besides the six different coffee options and the cup sizes you can change a variety of parameters as explained in chapters 10.1 through 10.6. 10.1 Changing the Grinder Fineness Important: You can only adjust the fineness during the actual grinding process. For darker beans, we recommend grinding somewhat coarser (turn the selector to the thicker bars, clockwise); for lighter beans, we recommend grinding somewhat finer (turn to finer bars, counterclockwise), see fig. 10. Please note: If coffee drips very slowly through the coffee spout, the coffee was ground too fine. Adjust to a coarser grind. If coffee flows too fast through the coffee spout, adjust to a finer grind. 10.2 The Program Dial (fig. 14) The Program Dial is located behind the door on the left side (fig, 1, 1b). It has a small black button in the middle. We call it the "P Button". During normal operation the Program Dial points to position 1. On the inside of the door you will find a card explaining the different positions. The program dial is used to: • change parameters (position 2, 3, 7, 8) • perform maintenance functions (position 4, 5, 6); see chapters 12.1 to 12.3. • check statistics (position 9); see chapter 12.5. Please note: On the back of the "door card" you will find additional information about the frothXpress system. 10.3 Changing the Coffee Temperature a. Turn the Program Dial to Pos. 2. The display shows TEMPERATURE/HIGH. Push the P Button once. The display will change to TEMPERATURE/REGULAR. Push it again and it will go back to high and so on. b. In HIGH the temperature of the coffee is approximately 7. F higher than in setting REGULAR. Please note: • The temperature of the coffee is also influenced by the grinder setting and the amount of coffee you are using. The finer the grind and the more coffee the machine grinds (e.g. in 1 CUP X STRONG) the more resistance the water has getting through the coffee thus increasing the temperature. •...
Ce manuel est également adapté pour les modèles :Cafetières - 158 (320.53 kb)