Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Continue with this process until the second group of 10 preset channels isloaded (upper group). Preset channels being previewed are displayed in the lower right corner. A black number on white background indicates that it is part of the lower group of channels and a White number on a Black background indicates that it is part of the upper group. 7 128-6374 7 of 12 DIRECT FM FREQUENCY SELECTION SPECIAL FUNCTIONS USING THE SHIFT BUTTON The selection of a specific FM frequency can be directly accessed us- There are a number of user preference functions that can be adjusted ing the appropriate code; these codes are presented as follows: simply by using the Shift (SFT) button with a specific number code. Thesefunctions are explained in the following paragraphs. In general, a shift/code is entered in the following manner: SFT SFT90 , where: (SFT) represents Shift button activation and XX represents the specific function code. (The 4-digit code always starts with 09.) CODE SELECTION 25 88.9MHz 26 89.1MHz 27 89.3MHz 4. Repeat the procedure in steps 2 and 3 to save nine other desirable channels for quick access. CODE SELECTION 21 88.1MHz 22 88.3MHz 23 88.5MHz 24 88.7MHz Figure 11. Modulator Frequency Codes NOTE: The default frequency is 88.5MHz PRESS AND HOLD ANY NUMBER BUTTON SYSTEM DEFAULT SHIFT CODE (0-9) TO COMMIT THE Defaults refer to the settings that are entered at the factory. When code 31 CHANNEL TO PRESET MEMORY is entered, the system is reset to the following defaults: 1. All channel presets cancel and revert to channel 184. 2. The LCD backlighting reverts to Green 3. Button confirmation tone is turned on. 4. All channels that were previously Locked Out or Skipped are reinstated LCD CONTRAST SHIFT CODE Figure 10. Setting Preset Channels To change the LCD contrast: 1. Enter code 35. 2. Use the Up and Down directional buttons to increase or decrease display contrast, respectively. 3. Press the SFT button to exit LCD contrast mode. 8 SELECT THE DESIRED CHANNEL THE PRESET MEMORY LOCATION APPEARS HERE SFT 0 4 7 1 5 8 2 6 9 3 The Joint KhrispOh Baby Oh Baby----------------------------------- CH 101 World 6 128-6374 8 of 12 LCD BACKLIGHT DIMMING SHIFT CODE To enable the LCD backlight dimming feature: 1. Enter shift code 36. 2. Use the Up and Down directional buttons to increase ordecrease display dimming, respectively. 3. Press the SFT button to exit LCD backlight dimming mode. . BUTTON CONFIRMATION TONE SHIFT CODE Normally, a beep confirmation tone is heard each time a button is pressedon the SCU. To silence this confirmation tone: 1. Enter code 40. 2. To turn the beep tone on again, enter code 41. LCD BACKLIGHT COLOR SHIFT CODES The backlight color for the LCD display can be either Green or Amber; toselect the desired color, enter one of the following codes: 1. Green------51 2. Amber----52 SCAN SET SHIFT CODES To invoke the Scanning mode of Normal Preset or Normal Non-Preset channels (in Normal mode only): 1. Normal Channel Scan-----60: Operation in normal mode, whereby channels can be scanned in sequential order, up or down. 2. Preset Channel Scan------61: Operation in this mode makes channel scanning possible only within the same category or group. CHANNEL/CATEGORY SELECTION SHIFT CODES To invoke the Channel(Normal)/Category selection mode: 1. Normal (SIRIUS Default Mode)-----80: Operation in normal mode, whereby channels can be selected in sequential order, up or down. “SIRIUS” Will be displayed in the lower portion of the LCD Screen. 2. Category------81: Operation in this mode makes channel changing possible only within the same category or group. CHANNEL SKIP SHIFT CODE If you wish to prevent acquisition of a particular channel during the channel selection process: 1. Recover Skipped Channels----90: Regain access to the channel by usingthe direct selection method to select the skipped channel; then enter code 90. (SFT+090+SFT) NOTE: This function can only be selected whendirectly accessing the channel(s) to be skipped. 2. Skip Channel----91: The channel will be skipped over duringchannel selection. (SFT+091+SFT) 3. Current Channel Parental Lock Out----92: Lock Out the current channel so that it may only be accessed with a chosen password. (SFT+092+SFT) NOTE: This function can only be sellected when directly accessing the channel(s)to be locked out. 4. Parental Lock Out Security Code Change----93: This code allows the user to change the Lock Out Security Code . (SFT+093+SFT) 5. Release Parental Lock Out----94: This code is used to Release the current Locked channel. (SFT+094+SFT) 6. Initialize Security Code ----98: This code is used to set and use a security code (password) into memory.(SFT+098+SFT) When this code isentered, “ENTER MASTER CODE” will be displayed. NOTE: DEFAULT SECURITY CODE = 0000 SYSTEM MASTER CODE = 1234 DISPLAY MESSAGES When problems are encountered during SIRIUS® system operation, amessage may appear on the display. The following table outlines themost common problems and provides a pr...
Ce manuel est également adapté pour les modèles :récepteurs radio - SIRIUS SRSIR-001 (519.07 kb)