You may also need an 8mm socket wrench or an 8mm drill bit for concrete. - Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. a b c d e A Guide spacer screw Guide spacer A 5 ENGLISH > If the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the closest location. But, do not change 2 or more locations from the designated spot. > Assemble the wall mount screw on 2 left and 2 right location on the top part and 1 left and 1 right location on the bottom part. > At this time, use a "+" driver (Manual or motorized) or 8mm wrench to tighten the screw so that the wall, wall bracket and Wall mount screw are completely pressed against one another. screw a. Locate and mark the centers of the wall studs using a stud finder. b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and then remove the wall bracket. c. Use a level to make sure your screw marks are level. d. Use the 4mm drill bit for wood to drill holes with the depth of 76mm or above where the wall mount screw location is marked on the wall. e. Clean the drilled hole. f. Tighten the wall mount screws for the wall bracket on the drilled hole. > At this time, tighten the screw so that the wall, wall bracket and the wall mount screw are pressed against one another. (Drywall can be damaged when tightened with excessive force, please be careful.) > When tightening the screw use the "+" driver (Manual or motorized) or 8mm wrench. 406mm drywall 76mm drywall wood stud 1. Set the display with the guide spacer assembled on the wall mount bracket on the wall in arrow direction. At this time, align the bottom assembly part and lift the set up lightly to align the top part. (When installing a Cinema Screen set (LM64**, LM66**, LM67**, LM76**, LM86**)to the wall mount, please refer to the installation section of the TV owner's manual.) 2. When adjusting the location, assemble the provide safety clip as shown in the picture to prevent the product from moving. Tighten the safety clip screw completely. If the safety clip is not tightened as shown in the picture, the product can fall off. > Pull on the bottom of the set to make sure the display is secure. > When installing a display rotated, only rotate the display 90 degrees (portrait mode). (Only applies for VESA 200X200, 400x400) > The clearance from the wall is 30mm ~ 41mm for this product. Make sure to keep a certain level of distance from the wall so that excessive force is not applied on the cable or accessory. > When you push the product with excessive force, the product can be damaged. 4 How to assemble the wall mount support and display - Always install the display with 2 or more people. * Assemble the wall mount support, product and safety clip. Safety clip Safety clip screw * Caution : Prevent the power cord from being pinched between the wall mounting bracket and the set when installing the set. (A pinched power cord may cause an electrical short) 6 5 How to level the Display After installing the display, check to make sure it is level. The wall mount has two screws that make minor adjustments to the level. 6 Cable arrangement and set protection cushion - Arrange the cables as shown in the picture. Use some type of cable banding device to hold all the cables together. - Attach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle. Attach the set protection cushion as shown in the picture. Product specification Model Name LSW420BX Width (mm) 440 Height (mm) 450 Depth (mm) 24 Weight (kg) 5.5 Wall Mount VESA Specification 400X400 Max.UL Load Capacity (kg) 50 Model Name LSW420BX Width (mm) 460 Height (mm) 450 Depth (mm) 30 Weight (kg) 7.2 Wall Mount VESA Specification 400X400 Max.UL Load Capacity (kg) 50 ± 10mm(Leveling) The display panel on Cinema Screen models (LM64**, LM66**, LM67**, LM76**, LM86**) can be easily damaged by pressure or shock. Please handle the product with care. For more information, please refer to the owner's manual of the TV. Please follow the below direction. 7 ENGLISH 30 41 223.9 234.9 130 9 31 31 290 31 31 9 25 400 450 30 400 30 460 20 400 20 440 [ Unit : mm ] MAX. MIN. 5.2 189.6 5.2 17 17 234 200 107.3 24 118.3 35 25 97.5 25 147.5 200 240 20 20 LSW220A 5.2 189.6 5.2 17 17 234 200 107.3 24 118.3 35 25 97.5 25 147.5 200 240 20 20 LSW220A 13±2° 15±2° MAX. MIN. 94.9 210 95.1 25 400 25 450 24 35 217.9 228.9 25 153.5 25 203.5 20 400 20 440 The model and serial number of the product is located Supported Displays on the back or one side of the product. Record it below (Please contract the retailers or refer to the TV owner’s should you ever need service. manual for applicable models.) ...
