Évaluations - 3, GPA: 3.7
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
(For storing measurement values, see p. 17.) • The pulse rate value is the beats per minute calculated based on the pulse rate during measurement. 3. To switch off the blood pressure monitor, press the On/Off Start button. • If you forget to switch it off, the blood pressure monitor will switch off automatically after approximately 5 minutes. SY^Dl* mmHg DIASTOLIC mmHg_ mss V 15 Flash warning system for hypertensive readings If the measured values fall within the hypertension range, the reading displayed on screen flashes on and off to alert user. According to JNC 7 Classification, values consistently In excess of 140 mmHg (Sys.) and/or 90 mmHg (Dla.) are considered to constitute high blood pressure. ment, always press the On/Off and Start button to turn off the unit and make sure to allow a rest period of 4 to 5 minutes before starting again. Please consult your doctor without delay If the blood pressure Indicator repeatedly draws attention to elevated blood pressure values. In general, blood pressure measurements are lower for the second measurement because you are less nervous and are more tranquil. For people who easily get tense, measuring twice each time Is very effective. When two measurements are taken, normally the smaller measurement Is stored. When taking two measurements, always stay quiet for 4 to 5 minutes after the first measurement before taking the second measurement. Diastolic (mmHg) Hypertension (Stage 1, Stage 2) 90 Prehypertension 80 Blood pressure readings will flash for approx. 6-seconds when In the high blood pressure range. Systolic blood pressure: 140 mmHg and over Diastolic blood pressure: 90 mmHg and over (Only when measurement is complete) Normal 120 140 (mmHg) Systolic When an Error Occurs During Measurement SYSTOLIC mmHg DIASTOLIC iwnHg An E will appear on the display to E Indicate that measurement was unsuccessful and should be performed Before performing another measure- Advice: 16 Storing Measurement Values This product can store 90 measurement values. After measurement, press the Memory/Recall button while the IE] mark is blinking. SYSTOLIC nwiHg DIASTOLIC mmHg 138 8? '-s? M/R fe OnfOfl Start Storing Is completed. * Up to 90 measurement values can be stored. When the memory Is full and additional values are stored, the oldest value in memory will be deleted and the new value will be stored. * If measurements could not be taken properly (the E mark is shown instead of the blood pressure value), measurement values cannot be stored. * However, even if the E mark is shown for the blood pressure value, the pulse value will still be stored. SYSTOLIC nutiHg DIASTOLIC mmHg 38 8? Æ k y' pulMrtnto. M/R OnfOfl Start Number of stored data To erase all measured values stored in memory: 1. Press the Memory/Recall button. The stored measurement values will be displayed. 2. Press the same Memory/Recall button again, and hold it pressed until the measurement values disappear (approximately 3 seconds or more). * It Is not possible to erase single measurement values. 3. The El mark and DO will be shown when all data Is deleted. To switch off the blood pressure monitor, press the On/Off Start button. ■ If you forget to switch it off, the blood pressure monitor will switch off automatically after approximately 5 minutes. 17 Recalling Stored Measurement Values Measurements can be recalled after measurement is completed or after the power has been switched off. • If no measurement values are stored, no value will be shown. M/R 1. Press the Memory/Recall button for the person whose data you want to recall. The average of all measured values in memory will be shown. ■ E3 will be shown at the top right of the display. • For example, if 90 measured values are stored, the average of the 90 measurements will be shown. (If only 1 measurement is stored, the ESI will not be shown.) SYSTOLIC rwiHg DIASTOLIC mmHg NB en--h M/R On/Off Start M/R 2. Press the Memory/Recall button again. Each time you press the Memory/Recall button, the previously stored measurement values will be shown in order, starting with the newest data. Do not press the Memory/Recall button for an extended length of time. If you hold the button pressed for approximately 3 seconds or longer, all data in memory will be erased, so please be careful. SYSTOUC mmHg DIASTOLIC M/R OnfOfl Start On/Off irt To cancell measurement value recall, press the On/Off Start button. If you forget to switch it off, the blood pressure monitor will switch off automatically after approximately 30 seconds. 18 After Use Storage 1. Unplug the plug from the main body. 2. Roll up the pressure cuff loosely and place the main unit Inside It. 3. Place the cuff and main body In the storage pouch. (Please take care not to create kinks In the tube.) • Do not place the AC adapter In the storage pouch. Specifications Power source DC 6V (Four AA/LR6 size alkaline batteries) AC 120V...