Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
7 Built-In Instructions — 8350 Series Note: Make Sure To Use Non-Combustible Material For Construction 25.25"Minimum 35.5" Maximum GFI Electrical Outlet For Rotisserie Motor (6.5 Amp Min.) 22.0"on center 38.25"9.4" 1.0" 19.25" Built-In Instructions w/o Trim Kit 3.5" max 2.5" max 1.75" max 1.75" max 1.75" max Top View Open Space Minimum Clearance to Open Hood 6" 25.25"Minimum 35.5" Maximum GFI Electrical Outlet For Rotisserie Motor (6.5 Amp Min.) 38.25"9.4" 20.25" 3.5" max 1.75" max 1.75" max 1.75" max Built-In Instructions with Trim Kit Top View Open Space Minimum Clearance to Open Hood 6" Additional Requirements: • Access doors required for drip tray removal. Some sort of access panel is required for removal or cleaning of the drip tray. • If using a backsplash apron or rear wall, locate electrical service on the left hand side for rotisserie motor construction. • A minimum clearance of 12” from the back of the outdoor cooking center must be maintained between the grill and any combustible construction such as wood siding of residence, 3” minimum for non-combustible construction. • The side vents on this unit can be covered for built in installations without danger of fire or without impairing the operation of the grill. 8 Natural Gas Installation — 8350 Series NOTE: Your 8350 Series grill is set up from the factory to use NATURAL GAS. If you want to use LP GAS, you must purchase the LP GAS CONVERSION KIT (sold separately). Please skip to the section titled “LP Cylinder Conversion - 8350 Series ”. WARNING Never attach an unregulated gas line to the appliance. Connection to an unregulated gas line can cause excessive heat or fire. YOUR NATURAL GAS COMPANY MUST INSTALL AND CONNECT THE GAS SUPPLY LINE TO THE GRILL. GENERAL INFORMATION Verify the type of gas supply to be used, either Natural Gas (N.G.) or Liquid Propane (L.P.), and make sure the serial plate agrees with that of the supply. Conversion kits are available separately for an additional cost which will enable you to convert your grill from L.P. to N.G. or to convert your grill from N.G. to L.P. Please see your local dealer for more information. NOTE: Always have a qualified service technician perform difficult conversions or modifications. For natural gas installations, an installer must supply a gas shutoff valve that is easily accessible to the grill. All installer supplied parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70-1990, and the National Fuel Gas Code, ANSI Z223.1-1998. All thread sealing compound must be an approved type and resistant to the actions of L.P. gases. Never use thread sealing compound on flare fittings. All gas connections should be made by a competent qualified service technician and in accordance with local codes and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code, ANSI Z223.1-1998. Gas conversions kits may be purchased separately. When ordering gas conversion kits, have the model number, and the type of gas (N.G. or L.P.) used for your grill. This grill and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.). This grill must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation of this grill must conform with local codes, or in the absence of local codes, with National Fuel Code, ANSI Z223.1a-1998. Installation in Canada must be in accordance with the Standard Can1-b149.1 and or .2 (installation code for gas burning appliances and equipment) and local codes. NATURAL GAS INSTALLATION The maximum inlet supply pressure is 10.5 inches w.c. for natural gas. The specified supply pressure is 7.0 inches w.c. for natural gas. Check your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas supply line is too small, the grill will not operate correctly. Any thread sealing compound used must be an approved type and be resistant to chemical breakdown resulting from the reaction with N.G. Attach the natural gas regulator (supplied with your grill) to the brass fitting coming out the bottom, right side of the grill (be sure the arrow on the regulator is pointing up towards the grill). Attach your gas line to the 3/8” flare fitting coming out of the natural gas regulator under the grill. NOTE: The gas line connection and the gas fitting must be the same diameter. Installer supplied shut-off valve (not included) - Place the shut-off valve in an accessible location to enable the gas supply to be cut off to the unit. NOTE: A flexible natural gas line is not included with Coleman® grills. Natural ga...
Ce manuel est également adapté pour les modèles :Greeley - 9992-648 (1.05 mb)