Évaluations - , GPA: ( )

Instructions White Mountain, Modèle VSR-18-1

Fabricant : White Mountain
Taille : 1.04 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

These chemicals are not harmful, but may produce annoying smoke and smells as they are burned off during the initial operation of the appliance, possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence. The initial break-in operation should last 2-3 hours with the burner at the highest setting. Provide maximum ventilation by opening windows or doors to allow odors to dissipate. Any odors remaining after this initial break-in will be slight and will disappear with continued use. OPERATION INSTRUCTIONS/FLAME APPEARANCE Manual - Figure 6 Millivolt - Figure 7 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS . Do not try to light any appliance. . Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neigh- bor’s phone. Follow the gas supplier’s instructions. . If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. VSM-(18, 24, 30) LIGHTING INSTRUCTIONS A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS . Do not try to light any appliance. . Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neigh- bor’s phone. Follow the gas supplier’s instructions. . If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. VSM-(18, 24, 30) LIGHTING INSTRUCTIONS LIGHTING INSTRUCTIONS WARNING . Any glass doors shall be opened when the appliance is in operation. . A fireplace screen must be in place when the appliance is operating and, unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction of combustion air. 1. STOP! Read the safety information above. 2. Push in manual gas con- trol knob slightly and turn clockwise to "OFF". Do not force. NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force. 3. Wait ten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow .B. in the safety information above. If you don’t smell gas, go to the next step. 4. Find pilot - follow metal tube from gas control. The pilot is in front of middle log on the right side. 5. Turn manual gas control knob counterclock- wise to .PILOT.. 6. Push in control knob all the way and hold in. Immedi- ately light the pilot with a match and the lighter rod that is provided with the burner. Continue to hold the con- trol knob in for about one (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 2 through 6. . If knob does not pop up when released, stop and immediately call a qualified service technician or gas supplier. . If the pilot will not stay lit after several tries, turn the gas control knob to .OFF. and call your service technician or gas supplier. 7. Turn manual gas control knob counterclock- wise to .ON.. GAS CONTROL KNOB SHOWN IN "OFF" POSITION TO TURN OFF GAS TO APPLIANCE 1. Push in gas control knob slightly and turn clockwise to .OFF.. Do not force. Page 10 14015-1-0903 1. Set the ON/OFF switch to "OFF". 2. Push in gas control knob slightly and turn clockwise to "OFF". Do not force. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result caus...