Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Used with a thermopile in a self-powered system. See Table 1 for model specifications. TABLE 1—MODEL SPECIFICATIONS. Model Primary Aerated Type of Orifice Pilot Tip Type Includes Q314A No Insert Target Includes natural and LP gas orifices, 1/4 in. compression fitting, “F,” “K,” or “L” tip styles, “B” mounting bracket, and “A” mounting bracket adapter. Q327A Yes Spud Target Includes natural and LP gas orifices, 1/4 in. compression fitting, and “B” mounting bracket with screws. Installation WHEN INSTALLING THIS PRODUCT… 1. Read these instructions carefully. Failure to follow instructions can damage product or cause a hazardous condition. 2. Check ratings given in instructions and on product to make sure product is suitable for your application. 3. Make sure installer is a trained, experienced service technician. 4. After completing installation, use these instructions to check out product operation. WARNING FIRE OR EXPLOSION HAZARD CAN CAUSE PROPERTY DAMAGE, SEVERE INJURY, OR DEATH Follow these warnings exactly. 1. Disconnect power supply before wiring to prevent electrical shock or equipment damage. 2. To avoid dangerous accumulation of fuel gas, turn off gas supply at appliance service valve before starting installation and perform Gas Leak Test after completion of installation. 3. Do not bend pilot tubing at the control or pilot after compression nut has been tightened. Gas leakage at the connection may result. Follow appliance manufacturer’s instructions if available; otherwise, use instructions provided below. LOCATION 1. Position pilot burner for easy access, observation, and lighting. In replacement applications, replace pilot burner with an identical unit and position new pilot burner in the same location and orientation as the original pilot burner. 2. Mount pilot burner on main burner. Mounting surfaces other than the main burner can shift, bend, or warp as furnace expands and contracts while operating. See Fig. 1. 3. Mount pilot burner so the ignition flame remains properly positioned with respect to the main burner flame. See Fig. 2. 4. Supply pilot flame with ample air free of combustion products. 5. Do not impinge pilot flame on adjacent parts. Do not impinge main burner flame on pilot burner. 6. Do not expose pilot flame to falling scale which could impair ignition of main burner. 7. Do not expose pilot burner to main burner rollout while igniting or extinguishing. 8. Do not expose pilot flame to drafts that push or pull pilot flame away from the thermocouple or thermopile. Fig. 1—Mount pilot burner on main burner. PILOT MUST BE RIGIDLY POSITIONED RELATIVE TO MAIN BURNER M1263 BURNER/GENERATOR J. H. • Rev. 12-92 • © Honeywell Inc. 1992 • Form Number 69-0519—3 ATTACHMENT NUT DESIGN ATTACHMENT NUT DESIGN PILOT BURNER/ IGNITION- SENSOR JUST RIGHT PILOT BURNER/ IGNITION- SENSOR TOO LOW PILOT BURNER/ IGNITION- SENSOR TOO HIGH MAIN BURNER FLAME WILL IMPINGE ON IGNITION- SENSOR IGNITION FLAME WILL IMPINGE ON MAIN BURNER IGNITION FLAME JUST MISSES MAIN BURNER M3285 CONNECT PILOT GAS TUBING 1. Cut tubing to desired length and bend as necessary for routing to pilot burner. Do not make sharp bends or deform tubing. Do not bend tubing at control after compression nut has been tightened, as this can result in gas leakage at connection. 2. Square off and remove burrs from end of tubing. 3. Push tubing into compression nut clearance hole until tubing bottoms. NOTE: When replacing a pilot burner or orifice, cut off old compression fitting and replace with new compression fitting provided with new pilot burner. Never use old compression fitting as it may not provide a gas-tight seal. See Fig. 3. 4. While holding tubing all the way in, engage threads and turn until finger tight. 5. Using a wrench, turn compression nut one turn beyond finger tight. DO NOT OVERTIGHTEN. 6. Connect other end of tubing to gas control according to gas control manufacturer instructions. Fig. 3—Always use new compression fitting. PILOT BURNER BODY FITTING BREAKS OFF AND CLINCHES TUBING AS NUT IS TIGHTENED TIGHTEN NUT ONE TURN BEYOND FINGER TIGHT TO GAS CONTROL M3295 INSTALL THERMOCOUPLE OR THERMOPILE PUSH-IN DESIGN 1. Insert thermocouple or thermopile tip into hole or barrel provided beneath pilot burner. See Fig. 4. 2. Push in firmly until thermocouple or thermopile is locked into place. 1. Insert thermocouple or thermopile tip into hole or barrel provided beneath pilot burner. See Figs. 4 and 5. 2. Engage attachment nut threads and tighten until thermocouple or thermopile is locked into place. Fig. 4—Installing thermocouple or thermopile. PILOT BURNER ASSEMBLY THERMOCOUPLE OR THERMOPILE PUSH-IN CLIP M3286 OPTIONAL ATTACHMENT NUT Fig. 5—Installing Q390 Thermocouple. SCREW-IN TYPE THERMOCOUPLE ATTACHMENT NUT ADAPTER PILOT BURNER ASSEMBLY M3269 INSTALL BLEED GAS TUBING (if used): 1. Route bleed gas tubing from bleed tapping on gas control to the pilot burner. 2. Push clip into place. See Fig. 6. 3. Insert bleed gas tubing until...
Ce manuel est également adapté pour les modèles :Greeley - TRADELINE Q327A (169.72 kb)