Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
8. Turn on control knobs to release gas pressure in hose. 9. Turn control knobs to "OFF" position. 10. Tighten any leaking connections. 11. Repeat soapy water test until no leaks are detected. 12. Turn off gas supply at cylinder valve until you are ready to use your grill. 13. Wash off soapy residue with cold water and towel dry. 14. Wait 5 minutes to allow all gas to evacuate the area before lighting grill. CAUTION: DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair service. Note: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are developing. WARNING PRE-START CHECK LIST: Property damage, bodily harm, severe burns, and death could result from failure to follow these safety steps. These steps should be performed after the grill has been assembled and prior to each use. DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual. PRE-START CHECK LIST: • Ensure that the grill is properly assembled. • Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being used. Replace with hose and regulator, Model No. 155-7741-0, which can be obtained by contacting customer service at 800-527-0717. • Leak check all gas connections and hose. See section on "Leak Testing". • Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces. • Position your grill on level ground in a well ventilated location, a safe distance from combustible materials, buildings and overhangs. • Properly place the empty grease tray under the grease drain hole in the bottom of the grill to catch grease during use. • DO NOT obstruct the flow of combustion and ventilation air. 10 LIGHTING INSTRUCTIONS: Follow the instructions exactly. 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the "OFF" position. 3. Turn on the fuel supply by rotating the cylinder valve knob counter-clockwise to full open. 4. DO NOT stand with head, body, or arms over the grill when lighting. LIGHTING THE MAIN BURNERS: 1. Open lid before lighting burner. 2. Make sure all control knobs are in the "OFF" position. 3. Select burner to be lit. Push and turn control knob of that burner to HIGH and continue to push knob in for 2 to 3 seconds to light burner. 4. If ignition does NOT occur in 5 seconds, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 5. Repeat Steps 3 & 4 for lighting each burner. 6. Refer to owner’s manual for match lighting procedure. 7. To turn off, turn control knob clockwise until it locks in OFF position. Note: If burner does not light or flame is too low, you may have spider or other insect blockage in burner, or the flow limiting device has been activated. See "Burner Assembly/Maintenance" under Proper Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP Cylinder and Hose/Regulator to Grill. MATCH LIGHTING THE MAIN BURNERS: 1. Open lid before lighting. 2. Turn the burner control knobs to "OFF". 3. Place a paper match in the end of the matchlighter. Strike the match and place approximately 1/2" (1 to 2 cm) from the burner lighting hole. Burner lighting hole is located inside left cabinet. 4. Turn on the FAR LEFT burner control knob to the "HIGH" position. The burner should light within 5 seconds. 5. If the burner does not light, turn the control knob to "OFF" and wait 5 minutes for gas to dissipate and repeat lighting procedure. 6. Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the "HIGH" position. 7. If the burner does not light within the first few attempts of match lighting, there is a problem with the gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the problem is found and corrected. See "Trouble Shooting" section of this manual. WARNING Match Lighting Hole Match- Lighter WARNING Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. LIGHTING THE ROTISSERIE BURNER: 1. Open grill hood before lighting rotisserie burner. 2. Make sure control knob is in the "OFF" position. 3. Push and turn control knob to HIGH and continue to push knob in for 3 to 5 seconds to light burner. 4. Once burner is lit, continue to push knob in for 30 seconds. 5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF”, wait 5 minutes to allow gas to dissipate and repeat light...