Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Total (5) connections. Connect the two wires [(a) and (b)] from switch wiring harness into the back of Electronic Ignition module. Total (2) connections, shown A. Note: Switch terminals are larger than electrode terminals and should only be installed in location shown as (a),(b). Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart right side panel with the nut, shown B. Insert AA battery into ignition module, negative (–) end first. Then put on the cap, shown C. 1 (a) (b) 2 3 4 5 ATie wrap NOTE: Wires omitted for clarity of illustration Electronic ignition module + - Cap AA battery Right side panelC BNutElectronic ignition Right side panel module 1414 Attach right side fascia to right side shelf using four #10-24x3/8”screws,5mm lock washers and 5mm flat washers, shown A. Insert flange on right side shelf into side shelf brackets on right side of firebox, shown B. #10-24x3/8” Screw 5mm Lock Washer 5mm Flat Washer A Bside shelf bracket 1515 Attach right side shelf using two 1/4-20x3/4” screws and 1/4” nuts, shown A. Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown B. Attach rear of shelf using one 1/4-20x1.” screw, shown C. A1/4-20x3/4” screw 1/4” nut Bscrew1/4-20x1.” #8x3/8” self-tapping screw Large flat washer C CLeft side shelf Side burner lid Hinge #8-32x3/8” screw CLeft side shelf Side burner lid Hinge #8-32x3/8” screw 16 Attach left side fascia to left side shelf using four #10-24x3/8”screws, 5mm lock washers and 5mm flat washers, shown A. Attach side burner lid handle to side burner lid using two #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown B. Place side burner lid onto left side shelf and align hinge holes in back of lid with shelf holes. Secure lid to the shelf using four #8-32x3/8” screws, 4mm flat washers, 4mm lock washers, and #8-32 hex nuts, shown C. Insert flange on left side shelf into side shelf brackets on side of firebox, shown D. ADLeft side fascia Left side shelf Left side shelf #10-24x3/8” screw 5mm Lock 5mm Flat washer washer washer side shelf bracket #10-24x3/8” Side burner lid handle screw B 5mm Flat washer 5mm Lock Side burner lid 4mm flat washer 4mm lockwasher #8-32 hex nut 1717 Attach left side shelf using two 1/4-20x3/4” screws and 1/4” nuts, shown A. . Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown B. Attach rear of shelf using one 1/4-20x1.” screw, shown C. A 1/4-20x3/4” screw1/4” nut #8x3/8” self-tapping Large flat washer screw B 1/4-20x1.” screw C 1818 First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fascia. Attach using two #8-32x3/8” screws and 4mm lock washers. Press sideburner control knob onto valve stem. #8-32x3/8” screw 4mmlock washer Control knob Side burner bezel Sideburnervalve bracket Sideburner fascia Valve stem Screws and Washersremoved from valve bracket Note: Use left and rightholes on fascia toattach valve bracket holes on fascia toattach bezel Note: Use upper and lower Note: Make sure set the bezel with longer slot at the top 19 Insert sideburner burner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on shelf, shown A.Secure burner to sideburner drip pan with one Wing nut, shown B. Under sideburner shelf, attachsideburner ignitor wire to electrode. Make sure burner tube engages sideburner valve, shown C. sideburner burner Wing nut electrode ignitor wire sideburner drip pan sideburner drip pan burner tube ABCvalve 20Place side burner cooking grate onto side burner shelf. 20Place side burner cooking grate onto side burner shelf. sideburner cooking grate 21 Insert the pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. Right door PRESS Top ofdoor pinon bottom of door 2222 Attach drawer front panel to drawer using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers. Drawer Drawer front panel #10-24x3/8” Screw 5mm Lock Washer 5mm Flat Washer Repeat for second drawer. 23Slide one drawer along lower tracks into cart left. Slide the other drawer along upper tracks into the cart. Drawer 24 2424 Place trough middle into fire box. Place troughs into fire box. Align pins at front of troughs with the holes at front of fire box. Troughs Trough middle Put trough middle on thebrackets at front and rear of firebox. Trough pin 25 Place cooking grates onto firebox as shown. Insert the four wire ends at rear of warming rack into holes in b...