Évaluations - , GPA: ( )

Instructions Emerson, Modèle ITONE IP100C

Fabricant : Emerson
Taille : 448.95 kb
Nom Fichier : 5ee5f518-bfa3-4a3d-8c6c-a99fd7f5e8cd.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

We have provided an Auxiliary Input Jack on (he back panel of this system and included a stereo connection cable so that you can still connect non-docking iPods®, other MP3 players, or personal CD players to this system. KB a9* Locate the stereo connection cable supplied with this system. Connect one end of the 3.5mm stereo cable into the auxiliary input jack (AUX) located on the back of the unit, and other end to the headphone or line out jack on your portable audio device. Set the POWER button to the 'On' position and (he FUNCTION button to the AUX position. Also turn on your externa) portable audio player. 129 m Use the VOLUME control to adjust the system volume. You may need to adjust your device volume, too. When you are finished listening set the POWER button to the ‘OfT position. Remember to shut off the power to your portable audio player as well. Important Note Remember to disconnect the stereo connection cable from the Aux Jack before inserting an iPod® in the docking station. 12 SETTING THE ALARM m 1C № ” S a 8-8 8 — ® " 8:38 ® Press and hold the ALARM SET button to enter the alarm Time setting mode. The front panel display will change from current time to alarm time. Note: The POWER switch must be set to the ’Off position to adjust the Alarm time. While continuing to hold the ALARM SET button press the HOUR button repeatedly until the display shows the desired wake-up hour. Be sure to observe the AM/PM indicator to confirm that you are setting the alarm time correctiy While continuing to hold the ALARM i|ET button press the MINUTE button repeatedly to se the desired wake-up minute. When the desired wake-up time appears on the display release ail the buttons. Press the ALARM ON/OFF button to activate the alarm. The ALARM indicatoron the front pane! will turn ‘On1. Set the FUNCTION selector to the desired alarm mode, Radio or Buzzer. To stop the alarm sooner, press the ALARM ON/OFF button once. The alarm stops immediately but the alarm indicator remains 'On' and the alarm will turn on again on the following day. To deactivate the alarm so that it does not repeal on the following day press the ALARM ON/OFF button once more. The alarm indicator goes 'Off'. TROUBLESHOOTING GUIDE Symptom | Possible Cause Solution Radio Noise or sound distorted on AM or Station not tuned properly for AM or FM. Retune the AM or FM broadcast station FM broadcasts. FM: Rod antenna is not extended. Extend FM Rod antenna. AM: The bar antenna is not positioned correctly. Reposition the unit until best reception is obtained. FM STEREO indicator does not light The BAND switch is not set to FM position. Set the BAND switch to FM ST. Position AM or FM, no sound Function switch is not set to RADIO. Set the Function switch to RADIO. Volume at minimum. Increase Volume iPod® Player Unit does not respond (no power) AC adaptor is not plugged into a wall outlet or the connector is not plugged into the power supply jack on the back of the unit. Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit. Using no or wrong iPod® insert Make sure the dock insert is the proper fit for the iPod® iPod®does not dock porperly iPod® did not install property Remove the iPod® from the dock and check for obstruction on the connections in the dock and on the iPod®,Then reseat it in the dock iPod® does not respond to the unit iPod® is not installed properly Remove the iPod® from the dock and check for obstruction on the connectors in the dock and on the iPod® Then reseat it in the dock iPod® is locked up Please make sure your iPod® is working properly before docking into the unit. Please refer to the iPod® manual for details. Using first or second generation iPod®, iPod® Shuffle or other devices. This unit cannot control those iPods® or other devices. iPod® did not charge up iPod® is not installed properly Remove the iPod® from the dock and check for obstruction on the connectors in the dock and on the iPod®. Then reseat it in the dock iPod® is locked up/frozen Please make sure your iPod® is working properly before docking into the unit. Please refer to your iPod® manual for details. iPod® battery has problem 14 i CARE AND MAINTENANCE If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes smudged or dirty, clean it with a soft, siightly dampened cloth. Never allow water or any liquid to get inside the cabinet. Never use any abrasive cleaners or cleaning pads as these will damage the finish of your unit. emerson warranty Consumer Electronics. Home Appliances and Home Officc Products Tliank you for choosing EMERSON! RGC Redmond Group gives the following express warranty to the original consumer purchaser or gift recipient for this EMERSON product, when shipped in its original container and sold or distributed in Canada by RGC Redmond Group or by an Authorized EMERSON Dealer: RGC Redmond Group warrants that this product is free...