Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Using an Indox V magnet with a flux density of 10,250 gauss, the damped, high compliance cone provides low frequency reproduction and smooth, extended frequency response equal to most larger speakers. The compact size of the 405A Speaker makes it ideal for public address systems in airports, buses, ships, aircraft, church pews and any installation that has need for a low level distribution system for wired music, program distribution and paging systems. Very smooth distribution is provided over a wide angle of 90° without high frequency loss. The wide angle of distribution, plus the small size of the unit allows greater separation between speakers with a substantial savings in speakers required. Clear, intelligible speech and good music reproduction is assured because of the extended 60 to 15,000 Hz range. Made of heavy grade steel, the entire 405A unit is designed for continuous, trouble-free service. The small size of the speaker, 4%" square by 2Vfc" deep make it possible to either front mount or rear mount the speaker in wall, partitions or ceilings and into volumes as low as 0.1 cubic feet. The solid, welded construction and water-resistant cone of the 405A prevents distortion in areas of high humidity. In line with other Altec speakers, the famed experience and engineering "know-how" has been built into the 405A Speaker, to make it the highest quality A" loudspeaker available. 1515 S. Manchester Ave., Anaheim, Calif. 92803 A Division of HtWM¡7Ling Altec, Inc. New York Features: 10 Watts Rating 90° Distribution Angle 60-15,000 Hz Response 4" Speaker Water Resistant Cone Thin Profile for Shallow Mounting High Sensitivity and Efficiency with Indox V Magnet Front or Rear Mounting EIA Standard Mounting for Square Shaped Speakers Low Cost Smooth Frequency Response Ideal for Multiple Installations Distortion Free Under High Humidity ИЙВаУД Л1ТГГ ALTEC 405А SPECIFICATIONS Power: Frequency Response: Pressure Sensitivity: E.I.A. Sensitivity: Impedance: Cone Resonance: Voice Coil Diameter: Distribution: Magnet: Type Structure weight 10 Watts music power Flux: 60-15,000 Hz 45 dB 8 Ohms 95 Hz 1" 90° Indox V 1% lbs. Terminals: 92 dB (SPL at 4 ft.) from Size: 1 Watt* 10,250 gauss Solder lug type 4% x 4% (square) x 2Va deep Mounting Data: Baffle opening 3%" diameter — Rear mounted Mounting bolt centers Weight: 4Hi" front mounted (4) equally spaced holes at 90° on 4%" diameter circle (.200 dia. holes) 2% lbs. *equivalent to EIA rating of 45 dB at 30 feet from 1 milliwatt ARCHITECTS AND ENGINEER SPECIFICATIONS The speaker shall be 4'%" square and shall have a sensitivity of 92 dB (SPL at 4 ft. from 1 Watt) measured on axis. The loudspeaker shall have a nominal impedance of 8 Ohms and a power rating of not less than 10 Watts with the frequency response uniform over the range of 60 to 15,000 Hz. Free air resonance shall not be higher than 70 Hz. The voice coil shall have a diameter of 1" and shall operate in a magnetic field of at least 10,250 gauss derived from a magnet of Indox V having a weight of 1% lbs. The speaker terminals shall be of the solder lug type. The speaker shall weight 2Xi lbs. and shall be able to perform efficiently in a volume as low as 0.1 cubic feet. It shall have a solid, welded construction and water resistant cone (to prevent distortion in high humidity areas). Any loudspeaker not meeting these requirements shall not be acceptable under this specification. The loudspeaker shall be Altec Lansing Model 405A. LITHO IN U.S.A. CP-48-5K Specifications and components subject to change without notice. Overall performance ivill be maintained or improved. AL-1716 -notice- We rccommcnd that you obtain your Altcc products from factory trained authorized Altcc Sound Contractors and Distributors. This will assure you of ]>ropcr installation, a continuing source of knowledgeable advice, scrvicc, and quick warranty protection....