|
Photos et spécifications Yamaha NS-B210 |
Facilité d'utilisation
If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. SUPPLIED ACCESSORIES NS-B210 Speaker cable (10m x 1) NS-C210 Fastener x 2 i En PLACING THE SPEAKERS For NS-B210 ■ Using as 2ch stereo speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. y 0 - -/ ■Using as front speakers and surround speakers in a surround system Position the speakers on both sides of the TV. The positioning of speakers is important, since this dictates the overall sound quality of the surround system. Set up the speakers on the basis of your listening position by following the owner’s manual supplied with your amplifier. And mount the speakers on a wall or place the speakers on a shelf. Determine the best position by following the owner’s manual supplied with your amplifier. ■ To mount the speakers on a wall by using the attached mounting bracket Fasten screws into a firm wall or wall support as shown in the figure, and hang the holes of the mounting bracket on the protruding screws. * Make sure that the screws are secured in the narrow sections of the holes. Tapping screw (3.5-4 mm) (1/8” to 3/16”) (Available at the hardware store) Diameter. 3.5 to 4 mm (1/8” to 3/16”) /, Wall or wall support 3 mm (1/8”) Min. 20 mm (13/16”) 26 mm (1”) You can also use the screw holes on the bottom of the speaker for installing the speaker using a commercially available speaker bracket (if you do not use the attached mounting bracket). Note Placing this unit too close to a CRT TV set might impair picture color or create a buzzing noise. Should this happen, move the speaker away (more than 20 cm (7-7/8”)) from the TV set. When using a PDP or LCD TV, it would not happen. WARNING • NS-B210 weighs 1.6 kg (3 lbs. 8 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out and the speaker may fall. This may damage the speaker, or cause personal injury. • Do not install the speaker on a wall with nails, adhesives, or any other unstable hardware. Long term use and vibrations may cause it to fall. • To avoid accidents resulting from tripping over loose speaker cables, fix them securely to the floor or wall. 1 En English For NS-C210 ■Using as center speaker Place the speaker on a TV rack or other stable surface. To prevent the speaker from falling down, attach the fasteners provided in each corner of the speaker’s underside. ■To mount the speakers on a wall by using the attached mounting bracket Fasten screws into a firm wall or wall support as shown in the figure, and hang the holes of the mounting bracket on the protruding screws. Make sure that the screws are secured in the narrow sections of the holes. Note Placing this unit too close to a CRT TV set might impair picture color or create a buzzing noise. Should this happen, move the speaker away (more than 20 cm (7-7/8”)) from the TV set. When using a PDP or LCD TV, it would not happen. WARNING • NS-C210 weighs 2 kg (4 lbs. 7 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out and the speaker may fall. This may damage the speaker, or cause personal injury. • Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength. • Thoroughly wipe clean the surface where the fasteners are to be attached. Note that adhesive strength is weakened if the surface is dirty, oily or wet, and that this may cause the center speaker to drop. • Do not install the speaker on a wall with nails, adhesives, or any other unstable hardware. Long term use and vibrations may cause it to fall. • To avoid accidents resulting from tripping over loose speaker cables, fix them securely to the floor or wall. Tapping screw (Available at the hardware store) 2 En CONNECTIONS TO YOUR AMPLIFIER Before making connections, make sure that the amplifier is switched off. ■ How to connect 1 Loosen the knob. 2 Remove 10 mm (3/8”) of insulation from each end of the cables, and twist the exposed conductors together neatly and tightly, as shown below. 10 mm (3/8 r Good No Good 3 Insert the bare wire. 4 Tighten the knob and secure the cables. Test the firmness of the connection by pulling lightly on the cables at the terminal. Notes • Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both. • Do not insert the insulation into the hole. Sound may not be produced. ■When using a banana plug Note Do not take off this cover unless using a banana plug. Cover 1 Remove the cover by pulling it toward you. 2 Tighten the terminal knob. 3 Simply insert the banana plug into the terminal. • Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of the amplifier (or receiver) with the speaker cable. • Connect t...
Haut-parleurs - NS-C210 (1.47 mb)