Simply insert the connections are faulty, no sound will be heard from the the Banana Plug connector into the corresponding terminal. speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit, your amplifier and/or speakers. How to Connect: Red: positive (+) Black: negative (–) 13 A Unscrew the knob. . Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] . Tighten the knob and secure the wire. 2 CONNECTING TO LINE OUTPUT (PIN JACK) TERMINALS OF THE AMPLIFIER • Leave the main speakers connected to the amplifier. • Amplifier line output terminals are generally labeled PRE OUT or SUBWOOFER OUT. * For PRE OUT terminal connection, the amplifier must possess at least two sets of PRE OUT terminals. With some amplifiers with only one set of PRE OUT terminals, connection can result in no sound from the main left and right speakers. In this case, select the method of connecting to the speaker terminals. • To connect with a YAMAHA DSP amplifier, connect the LOW PASS (or SUBWOOFER etc.) terminal on the rear of the DSP amplifier to either the left (L) or right (R) INPUT 2 terminal. If using one unit If using two units Notes • When connected to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of this unit. If connected, they will not produce sound. • When connecting to a monaural line output terminal of the amplifier, connect to either the left or right INPUT 2 terminal. 8 INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ON OFF AUTO POWER POWER HIGH CUT STANDBY-RED ON-GREEN VOLUME 50 Hz 150 Hz 0 10 INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS PRE OUT Amplifier Pin plug cords Left speaker Right speaker To AC outlet This unit LOW PASS INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ON OFF AUTO POWER POWER HIGH CUT STANDBY-RED ON-GREEN VOLUME 50 Hz 150 Hz 0 10 INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS ON OFF AUTO POWER POWER HIGH CUT STANDBY-RED ON-GREEN VOLUME 50 Hz 150 Hz 0 10 To AC outlet This unit Left speaker Right speaker Amplifier PRE OUT Pin plug cords To AC outlet This unit INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS English CONTROLS AND THEIR FUNCTIONS INPUT1INPUT2 FROM AMPLIFIER OUTPUT TO SPEAKERS ON OFF AUTO POWER POWER HIGH CUT STANDBY-RED ON-GREEN VOLUME 150 Hz 0 10 50 Hz INPUT1INPUT2 FROM AMPLIFIER OUTPUT TO SPEAKERS OFF AUTO POWER POWER HIGH CUT STANDBY-RED ON-GREEN VOLUME 150 Hz 0 10 50 Hz ON 15432 1POWER indicator Lights in green when the POWER switch is turned ON, and goes off when turned OFF. * STANDBY mode: If the AUTO POWER ON/OFF switch on the rear panel is set to ON, this indicator lights in red when no signal is input to this unit. 2POWER switch Turns the power of this unit ON and OFF whenever pressed. When this switch is turned ON, the indicator on the left of the POWER switch lights in green. 3HIGH CUT control Adjusts the high frequency cut off point. Frequencies higher than the frequency selected by this control are all cut off (and not output). * One graduation of this control represents 10 Hz. I00 90 II0 80 I20 70 I30 60 I40 50 Hz I50 Hz 4VOLUME control Adjusts the volume level. 5AUTO POWER ON/OFF switch By setting this switch to the ON position, this unit’s automatic power ON/OFF function operates as described below. If you do not need this function, set to the OFF position. * Make sure to change the setting of this switch only when the power of this unit is off. Automatic power ON/OFF function When you play a source, the power to this unit turns on automatically by sensing audio signals input to this unit. The power turns off automatically if the source being played is stopped or the input signal is cut off for several minutes. * This function will operate responding to a certain level of input signal. Increase the output level on the input source if the automatic power ON function will not operate, or decrease the level if the automatic power OFF function will not operate. * There may be a case that the power turns on unexpectedly by sensing noise from other appliances. If it occurs, set the AUTO POWER ON/OFF switch to the OFF position. This function is available only when the power of this unit is on (by setting the POWER switch (2) to “on”). ADJUSTING VOLUME POWER HIGH CUT VOLUME 150 Hz 0 10 50 Hz 2 5 1, 4 1 Set the VOLUME control to minimum. 2 Turn on the power supply to all the components. 3 Play any source and adjust the amplifier’s volume control to the desired listening level. 4 Turn up the VOLUME control gradually to adjust the volume balance between this unit and the main speakers. 5 Adjust the HIGH CUT control to the position...
)
