For safe and proper use of the speaker: • Position the speaker in a location that is solid, level, smooth, and low (with respect to the floor). • Do not push or apply pressure to the side of the speaker when moving, or lean objects against the side of the speaker. • Do not sit on or set objects on top of the speaker. Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). CONNECTIONS TO YOUR AMPLIFIER English Before making connections, make sure that the amplifier is switched off. CONNECTIONS • Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of the amplifier (or receiver) with the speaker cable. • One side of the speaker cable is red and the other side is black. Connect the (+) terminals on the amplifier (or receiver) and speakers using the red side. Connect the (–) terminals on both components using the black side of the cable. • Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. How to Connect: 1 Loosen the knob. 2 Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. 3 Insert the bare wire. 4 Tighten the knob and secure the cables. Test the firmness of the connection by pulling lightly on the cables at the terminal. SPEAKERS LR ++ –– 134Speaker (R) Speaker (L) Black Red Red Speaker output terminals of the amplifier (or receiver) Amplifier or Receiver Black Black When using a banana plug 1 Remove the cover by pulling it toward you. 2 Tighten the terminal knob. 3 Simply insert the banana plug into the terminal. 23Banana plug 1 Using the non-skid pads Put the provided non-skid pads at the four corners on the bottom of speaker to prevent the speaker from moving by vibrations etc. Non-skid pad Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. E-2 PLACING THE SPEAKERS Using as 2ch stereo speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. Using as main speakers in a multi channel system Position the speakers on both sides of the TV. The positioning of speakers is important, because it controls the whole sound quality of a multi channel system. Set up the speakers on the basis of your listening position by following the owner’s manual supplied with your amplifier. Rear Subwoofer Center NS-10MMF NS-10MMF Rear center Note This speaker features a magnetically shielded design, but there is still a chance that placing it too close to a TV set might impair picture color. Should this happen, move the speaker away from the TV set. REMOVING THE FRONT COVER The front cover is fastened to the enclosure at six points and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the six holes on the inner surface of the cover with the six corresponding pegs on the speaker and push gently. Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools. SPECIFICATIONS Type ................................ 2-way bass-reflex speaker system Magnetic shielding type Driver ................................... 9 cm (3-9/16”) cone woofer x 2 2.2 cm (7/8”) balanced dome tweeter Impedance ...................................................................... 6 . Frequency Response .................................. 55 Hz to 35 kHz Nominal Input Power .................................................... 70 W Maximum Input Power ................................................ 200 W Sensitivity ..................................................... 86 dB/2.83 V/m Crossover Frequency .................................................. 6 kHz Dimensions (W x H x D) .................... 179 x 898.5 x 234 mm (7-1/16” x 35-3/8” x 9-3/16”) Weight .................................................. 9.8 kg (21 lbs. 9 oz.) Accessories ................................................ Non-skid pad x 4 Speaker cable (4 m) x 1 . Specifications subject to change without notice due to product improvements. . Care should be taken not to exceed the input power values noted above. YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02...
)
