Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• Do not turn the volume of the subwoofer to maximum. Doing so may weaken the bass sound. Moreover, extraneous noise may be heard. • Selecting NORMAL or REVERSE with the PHASE selector reverses the polarity and may provide better bass reproduction in certain listening environments (depending on the type of front speakers, the position of the subwoofer and the adjustment of the BASSBOOST). It may also change the expansion and lightness of sound, and effect the feeling of the sound field. Select the setting that provides the sound you prefer when listening in your normal listening position. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. •Make sure all the connections have been correctly made. •Make sure the volume on the amplifier has been turned up properly. •Make sure the program source selector on the amplifier is set to the proper source. •Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. •Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker output. •Make sure all the connections have been correctly made. •Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. •Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. Specifications SA-FT3H For the U.S.A. model only AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 6 ohm loads, from 28 - 200 Hz; rated 150 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. SS-FRF3H (front/surround speakers) Speaker system 2 way, magnetically shielded Speaker units Woofer: 10 cm, cone type Tweeter: 2.5 cm, balanced dome type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 110 W Sensitivity level 84 dB (1 W, 1 m) Frequency range 140 Hz - 50,000 Hz Dimensions (w/h/d) Approx. 120 . 360 . 32 mm with table top stand Approx. 120 . 372 . 32 mm (Diameter of base: 190 mm) Mass Approx. 0.9 kg with table top stand Approx. 0.95 kg SS-CNF3H (center speakers) Speaker system 2 way, magnetically shielded Speaker units Woofer: 8 cm (. 2), cone type Tweeter: 2.5 cm, balanced dome type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 110 W Sensitivity level 84 dB (1 W, 1 m) Frequency range 150 Hz - 50,000 Hz Dimensions (w/h/d) Approx. 430 . 88 . 32 mm with table top stand Approx. 430 . 98 . 66 mm Mass Approx. 0.85 kg with table top stand Approx. 0.9 kg SA-WFT3 (subwoofer) Speaker system Active subwoofer, magnetically shielded Speaker units Woofer: 15 cm (. 2), cone type Enclosure type Acoustically Loaded Bass reflex Reproduction frequency range 28 Hz - 200 Hz Continuous RMS power output 150 W (6 ohms 100 Hz, 10% THD) Input LINE IN (input pin jack) General Power requirements North American model: 120 V AC, 60 Hz European model: 230 V AC, 50/60 Hz Others models: 220 ~ 230 V AC, 50/60 Hz Power consumptions 80 W 0.3 W (standby mode) Dimensions (w/h/d) Approx. 182 . 477 . 353 mm Mass Approx. 12 kg Supplied accessories Speaker cord (3.5 m) (3) Speaker cord (10 m) (2) Audio connecting cord (1) Table top stand cover (4) Table top stand base (4) Center speaker stand base (1) Center speaker stand adjuster (1) Cushion (20) Rear pad (10) Screw (M5) (5) Screw (M4) (2) Screw (M3.5) (16) Design and specifications are subject to change without notice. Raccordement du systeme acoustique Raccordez le systeme acoustique aux bornes d’enceintes de l’amplificateur. (D) Avant de raccorder les cordons, assurez-vous que tous les appareils (caisson de grave compris) sont hors tension. Remarques (E) • Assurez-vous que les bornes plus (+) et moins (–) des enceintes correspondent aux bornes plus (+) et (–) de l’amplificateur. • Veillez a bien serrer les vis des bornes d’enceintes, car des vis desserrees peuvent etre une source de parasites. • Veillez a inserer a fond les fils dans les bornes. Le contact des fils d’enceinte denudes au niveau des bornes de l’enceinte peut provoquer un court-circuit. • Pour les connexions cote amplificateur, reportez-vous au manuel fourni avec l’amplificateur. Conseil Les fils noirs ou rayes noirs ont une polarite negative (–) et doivent etre relies aux bornes moins (–) des enceintes. Emplacement des enceintes Position de chaque enceinte (F) Chaque enceinte doit etre dirigee vers la position d’ecoute. L’effet surround sera bien meilleur si toutes les enceintes sont a egale distance de la position d’ecoute. Installez les enceintes avant a une distance correcte a droite et a gauche du televiseur. Installez le caisson de grave a droi...