Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
• Be sure to tighten the screws of the speaker terminals securely as loose screws may become a source of noise. • Make sure all connections are firm. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. Micro Satellite System SA-VE225 4-233-675-11(2) WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not Cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus. To prevent fire or shock hazard, do not place vases on the apparatus. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment. For the Dolby Pro Logic If your amplifier is connected internally or externally with a Dolby Pro Logic processor, you should set the surround effect mode to “NORMAL” on the amplifier for your particular speaker system. For details on the setting procedure, refer to the manual that was provided with your amplifier. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. • Make sure all the connections have been correctly made. • Make sure the volume on the amplifier has been turned up properly. • Make sure the program source selector on the amplifier is set to the proper source. • Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. • Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker output. • Make sure all the connections have been correctly made. • Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. • Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. Specifications SS-V225 (Front and rear speakers) Speaker system Full range, magnetically shielded Speaker units 5 . 9 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 100 watts Sensitivity level 86 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 70 . 151 . 126 mm, including front grille Mass Approx. 550 g each SS-CN225 (Center speaker) Speaker system Full range . 2, magnetically shielded Speaker units 5 . 9 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 120 watts Sensitivity level 88 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 301 . 70 . 126 mm, including front grille Mass Approx. 1.1 kg SA-WMS225 (subwoofer) Speaker system Active subwoofer, magnetically shielded Speaker unit Woofer: 16 cm, cone type Enclosure type Advanced SAW type Amplifire section Continuous RMS power output 50 W(8 ohms, 20 - 150 Hz, 0.8% THD) Reproduction frequency range 28 Hz - 200 Hz High frequency cut-off frequency 200 Hz Inputs LINE IN (input pin jack) SPEAKER IN (input terminals) Outputs LINE OUT (output pin jack) SPEAKER OUT (output terminals) General Power requirements 220 - 230 V AC, 50/60 Hz Power consumptions 50 W Dimensions (w/h/d) Approx. 205 . 385 . 385 mm, including front grille Mass Approx. 10.5 kg Supplied accessories Foot pads (20) Monaural connecting cord (1 phono to 1 phono) (1) Speaker connecting cords, 10 m (2) Speaker connecting cords, 3.5 m (3) Speaker connecting cords, 2.5 m (2) Design and specifications are subject to change without notice. DAABBCenter Centre Subwoofer Caisson de grave Rear(Right) Arriere (droite) Front (Left) Avant (gauche) Rear(Left) Arriere (gauche) Foot pads Tampons autocollants EHGFPOWER POWER indicator Indicateur POWER LEVEL MODE WS-WV10A (for rear speakers) (pour les haut- parleurs arriere) Foot pads Tampons autocollants Front (Right) Avant (droite) English Lorsque le “Raccordement B” est utilise (Reglage des enceintes) Pour Reglez sur Enceintes frontaux LARGE Enceinte centrale SMALL Enceintes arrieres SMALL Caisson de grave OFF (ou NO) Pour le Dolby Pro Logic Si votre amplificateur est raccorde interieurement ou exterieurement a un processeur Dolby Pro Logic, selectionnez le mode d’effet sonore “NORMAL” sur l’amplificateur pour votre systeme acoustique particulier. Pour les details sur le reglage proprement dit, reportez- vous au manuel fourni avec l’amplificateur. Guide de depannage En cas de probleme, veuillez verifier les points de la liste suivante et prendre les mesures necessaires. Si le probleme persiste, consultez votre revendeur Sony. Le systeme acoustique ne f...