Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions Sony, Modèle NAS-50HDE

Fabricant : Sony
Taille : 2.78 mb
Nom Fichier : 2890158111.pdf
Langue d'enseignement: en
Aller à la télécharger



Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


© 2007 Sony Corporation GB Connections UK model only . Connect the speaker cords to the speakers. Insert the cords into the speaker terminals on the speakers. Pull on the cord lightly afterwards to confirm that the cords are firmly connected. RedBlackRedBlack Note Make sure the metal leads (not the part covered with vinyl insulation) are securely inserted into the speaker terminals. . Connect the speakers to the unit. Connect the cords to the SPEAKER terminals on the unit. After connecting the speaker cords and while facing the front of the unit, place the speaker connected to the “R” terminal to the right and the speaker connected to the “L” terminal to the left. RightLeft Note Make sure to keep the speaker cords away from the antennas as they may produce noise in the radio reception. GB . Connect the AM loop antenna. Connect the AM loop antenna to the AM antenna terminals on the unit. Pull on the cord lightly afterwards to confirm that the antenna is firmly connected. Notes . Make sure to keep the AM loop antenna away from the unit or other AV equipment as this may produce noise in the radio reception. . Make sure the metal leads (not the part covered with vinyl insulation) are securely inserted into the antenna terminals. . Connect the FM wire antenna. Connect the FM wire antenna to the FM antenna jack on the unit. FM wire antenna Notes . Make sure not to wind the FM wire antenna up during use. . After connecting the FM wire antenna, lay it out so that it is as parallel to the floor as possible. . Connect the DAB wire antenna (UK model only). With a DAB external antenna, you can obtain a higher DAB broadcast sound quality. We recommend that you use the supplied DAB wire antenna only temporarily until you install a DAB external antenna. Connect the supplied DAB wire antenna to the DAB jack on the unit. DAB wire antenna Tip To install the DAB external antenna (optional), 75 . coaxial cable with F male type connector (optional) will be needed. . Connect the unit to a network. If you have a network environment, you can easily connect the unit to the Internet as shown in the figure below. . Disconnect the network cable from your computer. . Connect the network cable to the unit. Continued . Notes . This method of accessing the Internet may not be possible for some Internet service provider. . While the network cable is connected to the unit as described above, you will not be able to access the Internet on the computer. If you want to connect to the Internet from the unit and the computer at the same time, you must use a separate network cable to connect the computer to the network. For details on connections, refer to the page 85 of the Operating Instructions or the customer support site of Sony Europe, support.sony-europe.com/ (for the customers in Europe only). . Connect the power cord. Connect the power cord to a wall outlet after all other connections have been made. The unit turns on automatically and starts making the initial settings. Wait until the unit turns off again. The initial settings may take a few minutes depending on the unit’s condition. WARNING Do not disconnect the power cord while the initial setup is in progress. Doing so may cause the unit to malfunction. Inserting the batteries into the remote control Insert two size-AA (R6) batteries (supplied) into the remote control with the . and . terminals matching the polarity markings. When the remote control is no longer able to operate the unit, replace both batteries with new ones. Setting up the AM loop antenna 1 Unroll the antenna cord from the antenna. Antenna cord 2 Assemble the AM loop antenna so that it stands vertically. Unfold the stand, raise the antenna vertically and insert it into the slot as shown in the figure below. GB Listening to CDs, Radio Broadcasts, or DAB services Listening to an audio CD 1 Press CD.. The disc tray slides out. CD. 2 Place an audio CD into the disc tray. Load a CD with the label side up. 3 Press CD.. The disc tray closes and playback starts. When an audio CD is loaded, the unit automatically starts searching for title information within its database or over the Web (when connected to the Internet). CD. To stop playback Press .. . To perform other operations on the remote control To pause playback Press .. To select the previous/next track Press ./.. To fast rewind or fast forward Press and hold down ./.. GB Listening to the radio 1 Press FM/AM. Press the button repeatedly to select FM or AM. FM/AM 2 Press TUNING + or TUNING – on the remote control to tune in a station. TUNING +/– Listening to DAB services (UK model only) 1 Press DAB. DAB Auto Scan starts automatically. When scanning is completed, the DAB service that was first received starts. DAB To perform other operations on the remote control To select different services Press ./.. To switch between the primary and secondary components Press ./.. Listening to CDs, Radio Broadcasts, or DAB services (continued) GB Using the Hard Disk Drive For ...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories