4"x 6" 5"x 7" 6"x 9" 6"x 9" 6"x 9" Description 2-Way 2-Way 2-Way 2-Way 3-Way Impedance 4 Ohms 4 Ohms 4 Ohms 4 Ohms 4 Ohms Freq. Resp. (Hz) 60-20,000 50-20,000 40-20,000 40-20,000 40-20,000 Sensitivity (dB) 90 91 92 90 92 Power Handling 75 Watts 100 Watts 150 Watts 200 Watts 150 Watts Features Cone (Polypropylene) X X X X X Installation Speaker Grilles X X X Speaker Wire X X X X X Hardware X X X X X Mounting Dia. 4"x 6" 5"x 7" 6"x 9" 6"x 9" 6"x 9" Mounting Depth 2" 2-1/2" 3" 3-1/2" 3-1/2" -2 PRE-

All they require is directional placement. (See tip No. 2.) No. 6: Never let any part of the speaker (except the mounting flange) touch any part of the car. You’ll be amazed what noises a speaker (and your car) can produce when one touches the other. No. 7: Don’t skimp on the quality of the speaker wiring. All Audiovox speakers include wiring rated to properly transmit the normal power load the speaker is designed for. -3 INSTALLATION INSTRUCTIONS CAUTION: Do not mount the speakers in the follow

Typical Speaker Mounting and Grille Installation -6 This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s) or markings. THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S

They are not always the best places for sound reproduction. Using Factory Openings -The one advantage to using the factory openings is you avoid having cut sheet metal, as the holes are pre- punched. You normally have only to cut away thin plastic or fiber panels that conceal the openings. Openings near the floor should be avoided if at all possible. Be Innovative -If you’re mechanically inclined, remove door panels, dash, side panels, etc., and really get into the basic construction of the car.

Occasionally, you’ll find a 5” or 5-1/4” round hole. Selecting the Speaker Location Use the following guidelines to select the speaker location: 1. Examine the deck panel thoroughly. Observe movement of the trunk springs, trunk lid, support hinges, power antenna, etc. Obviously, you don’t want to install a speaker where the arc of a moving trunk support would interfere with the speaker grille. Avoid all areas that might cause interference with the normal functions of the trunk lid and/or antenna

You normally have only to cut away thin plastic or fiber panels that conceal the openings. Openings near the floor should be avoided if at all possible. Be Innovative -If you’re mechanically inclined, remove door panels, dash, side panels, etc., and really get into the basic construction of the car. You’ll be amazed at the vast amount of good-toexcellent speaker locations a car can conceal. If You Don’t Wish to Cut Holes - Consider the hang-on or surface- mount type of speakers. Just pick a reas

2. Place the speaker into the opening and check for proper fit. Remove the speaker and replace the paper door liner previously removed. Selecting the Speaker Location 1. This is a good speaker location , but to use it, you’ll have to enlarge the existing hole 2. Check for free window crank movement 3. Check for possible braces behind selected area with window down andup 4. This is a poor location for a speaker installation; it is too low and behind driver’s hearing area Speaker Mounting Let’s as

-5 1. Using the template provided (we’ll assume you’ve already made all the necessary checks and you’ve not going to cut through the door release mechanism), mark the speaker opening on the door panel. Now carefully cut the opening and drill the required holes. NOTE: Whether you’re using an existing hole, or have just cut or modified an existing opening as described above, you are now ready for speaker installation. 2. Place the speaker into the opening and check for proper fit. Remove the speak

This is far more critical when installing large power producing woofers. Mount your speakers securely! If the speaker has four mounting holes, use all of them. No. 4: Woofers need “breathing” room! For a speaker to perform efficiently, it must move large amounts of air. If you restrict this airflow (try to fit a large speaker in a small space or if you undercut the recommended mounting hole size), you won’t have an efficient speaker. Conversely, the enclosure you mount them in should be somewhat

3-1/2" 4" 5-1/4" 6-1/2" 6-1/2" Description 2-Way 2-Way 2-Way 2-Way 2-Way Impedance 4 Ohms 4 Ohms 4 Ohms 4 Ohms 4 Ohms Freq. Resp. (Hz) 100-21,000 80-20,000 60-20,000 50-20,000 40-20,000 Sensitivity (dB) 89 90 91 91 91 Power Handling 60 Watts 75 Watts 100 Watts 100 Watts 125 Watts Features Cone (Polypropylene) X X X X X Installation Speaker Grilles X X X X Speaker Wire X X X X X Hardware X X X X X Mounting Dia. 3-1/2" 4" 5-1/4" 6-1/2" 6-1/2" Mounting Depth 1-9/16" 1-3/4" 1-3/4" 2-1/2" 2-1/2" -2 P