5Memorizes the current Audio Setup and AV Interface settings. 6Clears the currently memorized settings. 7Returns to "SETUP Memory" screen. Audio Setup and AV Interface settings can be memorized. The memorized settings can be recalled at any time. For example, even when the settings are cleared due to replacement of the battery, the settings can be restored. 1 Display the SETUP Memory screen Setup Memory Touch in the "SETUP Menu" screen (page 62). 1 Locks the Audio Setup and AV Interface settings. When Lock is selected, you cannot set the Audio Setup and AV Interface settings. 2 Memorizes or recalls the settings. To cancel the function, touch No . To cancel memorization, touch No . The SETUP Menu screen appears again. 3 Returns to the original screen. Start Setup Memory 3 Memorize or recall the settings When memorizing the Audio Setup and AV Interface settings: If settings have already been memorized, a confirmation message appears. Touch Yes . To cancel memorization, touch No . When recalling the memorized settings: Touching the screen displays a confirmation message. Touch Yes . To cancel recalling, touch No . When clearing the currently memorized settings: Touching the screen displays a confirmation message. Touch Yes . To cancel clearing, touch No . Quit memorization/recalling of settings 4 DNX7120/DDX712/DDX7032 EXT SW Setup Setting up power specification of the external device for which the power is controlled from this unit. 1 Display the EXT SW SETUP screen Touch in the "SETUP Menu" screen (page 62). 2 Perform EXT SW Setup Setting EXT SW Control 1 (EXT SW1) Setting EXT SW Control 2 (EXT SW2) The setup method is the same as "EXT SW1". 1 2 3 4 1 Sets the name of the external device. See (page 49) for information on how to enter the name. 2 Sets the power signal output mode. ( EXT SW1: Pulse, EXT SW2: Level) Pulse: Generates a single power signal pulse. Level: Continues output of high power signal. Sets to turn output on/off each time the button on the EXT SW Control screen is pressed. 3 Sets the Pulse signal output time. Outputs 500ms when "1" is set. Increases by 200ms with each step. Up to 100 steps can be set. 4 Returns to the original screen. English Audio Control Audio Control Menu Displays the Audio Control menu to set the sound effect function of this unit. 1 Display the control screen of any source Press several times until the control screen appears. 2 Display the Audio Control menu 3 Select the Audio Control item 1 1Switches to the selected Audio Control screen. You can adjust the front/rear and right/left audio balance. 1 Display Audio Control screen Touch in the "Audio Control Menu" screen (page 86). 2 Set the each item 2 4 4 3 3 1 5 6 7 1Moves to the "Audio Control 2" screen. 2Adjust the front/back and left/right volume around the touched area. 3Adjusts the right and left volume balance. 4Adjusts the front and rear volume balance. 5Turns the Loudness control function On or Off. If turned "On", high and low tones are automatically enhanced during low volume. 6Displays the present source information. The stream (Dolby Digital, dts, Linear PCM, MPEG, MP3, WMA or AAC) is displayed. 7Returns to the "Audio Control Menu" screen. Audio Control 8 9 10 11 8Returns to the "Audio Control 1" screen. 9Adjusts the volume of the present source based on the difference level of original volume. DNX7120/DDX712/DDX7032 p Adjusts the subwoofer volume. q Returns to the "Audio Control Menu" screen. . • If you have increased the volume first, then reduced the volume using the "Vol. Offset", the sound generated if you suddenly switch to another source may be extremely loud. • You may not set some models of power amp boost to "+18". See the catalog or instruction manual of power amplifier. Equalizer Control You can setup the equalizer. 1 Display Equalizer Control Touch in the "Audio Control Menu" screen (page 86). 2 Display the Equalizer screen 2 4 3 1 1 Selects an equalizer curve type. You can select any of the following equalizer curves. • "Natural" • "Rock" • "Pops" • "Easy" • "Top40" • "Jazz" • "User" . • "User" can be selected after tone adjustment is carried out. See (page 88). 2 Selects items to be adjusted for tone curve setup. If turned "Off", only Level can be setup for tone curves. 3 Displays the Tone curve setup screen. (page 88) 4 Returns to the "Audio Control Menu" screen. English Audio Control Tone Setup You can set a Tone curve. 1 Display the Tone screen See (page 87). 2 Set the Tone 1 2 3 4 5 6 7 8 9 1 Tone curve becomes flat. 2 Bass adjustment items are displayed. 3 Middle adjustment items are displayed. 4 Treble adjustment items are displayed. 5 Sets the Center frequency. 6 Sets the level. 7 Sets the Q factor. (Only Bass and Middle can be set) 8 Bass DC Extend settings. (Only when Bass is selected) If turned "On", it extends the bass center frequency to the low register by approximately 20%. 9 Returns to the "Equalizer" screen. Zone Control You c...
)
