Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
AJ6110 QSG-Eng 4/10/06 1:52 PM Page 2
Mount it
C
3
• Manually fasten the 8 long screws down into the spacer holder holes to mount your set. Start
Ask a friend to help out. An extra hand to hold
screwing at opposite corners of the unit for better support.
the unit makes mounting easier and quicker
A
Template
C
A
• Cut the template to fit inside the cabinet.
• Align the template border marked "FRONT" along the
front edge of your cabinet.
• Use adhesive tape to fix the template.
• Drill 1/4 inch holes, as marked X on the template.
• Remove the template when you finish drilling.
Tip
Tip
To prevent damage to your
– Clean the bottom of the cabinet surface and also empty your cabinet before mounting.
set, do not use an electric
– Place the unit in a clean, safe place when drilling to avoid wood shavings dropping into the
drill to secure screws when
ventilation slots.
mounting!
– Use a nail to start each drill hole.
– Drill from the bottom upwards if you do not have enough room inside the cabinet.
– If the overhang is more than 1 1/4 inch, use
– Hold your drill firmly at 90o with the cabinet bottom and drill holes at low speed.
longer screws (not included).
– Clear wood shavings.
B
Using the spacers
B
On the spacers, there are 4 pairs of notch length
options. Depending on the thickness of you cabinet bot-
Spacer
tom (with/ without an overhang), these notch lengths
L (Low)
correspond to the 4 notch height in the space holders,
L••H (4 heights)
and allow you to adjust to the best height to help you
Arrow
H
L
mount the unit.
• Measure the height of the cabinet bottom and/over-
hang.
• Turn the spacer counterclockwise to determine
which of the 4 heights is most suitable: Low • •
High. Align to the arrow indication.
• Insert the spacers accordingly.
Use it
C
4
Playing discs
For full details, please read and follow the instructions inside the User manual.
1 Press POWER to on, then press CD/AM/FM
once or more to select CD source.
A
2 Press 0 EJECT to open the CD compartment
Setting the clock
3 Insert a disc with the printed side facing up.
1 On the set, press and hold CLOCK.
Press 0 again to close the compartment
➜ The hour digits start flashing (AM 12: 00 by default).
➜ Playback starts automatically. Display shows
MP3-CD / CD-R / CD-RW COMPATIBLE
current track number
M I C R O S Y S T E M
M C M 7 6 0 M I C R O S Y S T E M
2 Hold down or press ∞ or § repeatedly to set the hour.
4 To pause playback, pressÉÅ. To resume playback,
3 Press CLOCK to confirm the setting.
press the button again
➜ The minute digits start flashing.
5
To stop playback, pressÇ
4 Repeat step 3 to set the minute.
➜ Display shows the total number of tracks
5 Press CLOCK to confirm the setting.
D
To turn on the Daylight Saving Time (DST) mode
Tuning to radio stations
1 In the standby mode, press and hold DISP on the set.
➜ Current time setting moves ahead by 1 hour.
1 Press POWER to on, then press then press
DST appears.
CD/AM/FM once or more to select radio source
2 Press DISP again.
(AM or FM)
➜ The set returns to normal time setting. DST disappears.
2 Press and hold ∞ / § until the frequency in the
display starts running
➜ The radio automatically tunes to a station of
B
sufficient reception
3 Repeat step 2 if necessary until you find the desired
Setting the timer
radio station
1 On the set, press TIMER to activate.
➜ To tune to a weak station, press ∞ / § briefly
➜ 015 flashes. TIMER appears
and repeatedly until optimal reception is found
2 Turn the TIMER control counter-/clockwise to
adjust your timer period (from 1 to 180 minutes).
➜ Display shows selected timer period.
Tip
To Improve radio reception:
3 Press TIMER to confirm.
– For FM, extend and adjust the AC power cord
➜ Timer period starts to count down. TIMER flashes
4 To cancel the timer, press TIMER during the countdown.
➜ Display shows the clock time.