Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Doing so could cause the child seat not to perform as intended. Forward-Facing Installation Forward-Facing Installation 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Route the vehicle seat belt through the forward-facing belt slots, then buckle. Ensure the vehicle belt is not twisted. 5 Push the child seat down while pulling the vehicle belt to remove all slack (see pages 10 – 11). 6 Attach and remove slack from the Versa-Tether (if an anchor point is available). 7 Store excess webbing in the elastic strap. 8 Replace the cover. 1b1a45 52 Checklist9Check that the vehicle belt is securely fastened. 9Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9Check that any excess Versa-Tether® webbing is contained within your vehicle and secured in the elastic strap. Forward-Facing Installation Check Versa-Tether® (Top Tether) attachment Check buckle connection Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat Check that Versa-Tether® (Top Tether) webbing is stored in the elastic strap Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Checklist9Check that the vehicle belt is securely fastened. 9Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9Check that any excess Versa-Tether® webbing is contained within your vehicle and secured in the elastic strap. Forward-Facing Installation Check Versa-Tether® (Top Tether) attachment Check buckle connection Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat Check that Versa-Tether® (Top Tether) webbing is stored in the elastic strap Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path 53 Aircraft Installation Aircraft Installation This child seat is certified for aircraft use. Most airlines in the U.S. and Canada will allow the use of a child seat as long as it is labeled as an approved child seat for use in aircraft and fits properly on the aircraft seat. Contact the airline about their policy prior to traveling. The FAA recommends that a child weighing up to 40 lbs (18.1 kg) use a certified, harnessed child seat while traveling on an aircraft. Install your child seat in a window seat to avoid blocking the aisle. Rear-Facing Installation For rear-facing aircraft installation (Fig. A), follow Rear-Facing Lap Belt Installation instructions on pages 38 – 41. Forward-Facing Installation For forward-facing aircraft installation (Fig. B), follow Forward-Facing Lap Belt Installation instructions on pages 50 – 53. If the aircraft lap belt is too short, ask a flight attendant for a belt extender. NOTE: Your child may experience discomfort if the buckle is located in the seating area of the child seat after installation. Ab 54 Securing Your Child WARNING! • Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. • Adjust the harness to fit the clothes the child is wearing. Remove bulky coats and/or jackets before putting the child in the child seat. • The HUGS™ chest pads must be used at all times when installing the child seat forward-facing. • Verify that the child seat is secure and the harness is properly adjusted around the child each time the child seat is used. Before You Begin: • Follow the instructions on pages 18 and 19 to make the proper adjustments to the harness and buckle. * Rear-facing 5 – 40 lbs (2.3 – 18.1 kg) position 3 only. * Forward-facing 20 – 70 lbs (9.1 – 31.8 kg) AND 1 year of age. Position 1 or position 2 may be used. Securing Your Child WARNING! • Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. • Adjust the harness to fit the clothes the child is wearing. Remove bulky coats and/or jackets before putting the child in the child seat. • The HUGS™ chest pads must be used at all times when installing the child seat forwa...