Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
• Lap Belts Forward of Seat Crease 13 5.2.2 SAFE Vehicle Belt Systems THE FOLLOWING BELT SYSTEMS CAN BE USED WITH YOUR CAR SEAT, IF the seat location meets all other requirements of these instructions and those in your vehicle owner's manual. LATCH can be used in place of the following vehicle restraint systems if your vehicle is equipped with LATCH anchor points. Please refer to vehicle owners manual for LATCH locations. For Built-in Harness Only • Lap Belts - Manually Adjusted When buckled, the belt is tightened manually by pulling on the excess belt. • Lap Belts with Automatic Locking Retractor (ALR) The automatic locking retractor will not permit the lap belt to lengthen once it is buckled. Tighten the belt by feeding the belt back into the retractor while pushing down hard on the car seat. 14 With OR Without Built-in Harness • Combination Lap/Shoulder Belt with Locking Latch Plate Once it is buckled, this type of belt has a latchplate that will not allow the lap portion of the belt to loosen. Belt is tightened by pulling hard on the shoulder portion of the vehicle belt while pushing down hard on the car seat. • Combination Lap/Shoulder Belt with Sliding Latch Plate This belt has a latchplate that slides freely along the belt. WITH Built-in harness: This belt MUST be converted to prevent movement of the lap portion of the belt. You must use the locking clip provided with the car seat, unless your vehicle's seat belt can be converted in another Locking clip way as described in your vehicle owner's manual. WITHOUT Built-in harness: Conversion or locking clip are not needed. 15 To Install Locking Clip: 1. Tighten the buckled belt by pushing down hard on the car seat and pulling hard on the shoulder belt. 2. While pushing down on seat, pinch the two straps together behind the buckle tongue. Unbuckle the belt without allowing it to slip. 3. Connect lap and shoulder belts as shown . 4. Rebuckle belt. Check that lap belt does not move by pulling hard. If belt loosens or lengthens, repeat procedure. Remove locking clip when not using car seat. Store under it’s tab on the back of seat. . “ (1.25 cm) 16 With LATCH Newer vehicles have one or more seating positions with LATCH anchorage systems. If vehicle is equipped with LATCH, the vehicle lower anchor points may be visible at the vehicle seat crease. If not visible, they may be marked with the symbol below . See your vehicle owner’s manual for exact locations, anchor identification, and requirements for use with a car seat. Typical seat in a passenger vehicle. Other vehicle types may have different LATCH locations. Vehicle Top Tether Anchor Points Vehicle Lower Anchor Points Vehicle Seat Crease Check vehicle owner’s manual for vehicle top tether anchor locations. They may be identified using one of the anchor symbols as shown above . or . ONLY use LATCH on a car seat in a seating position recommended by vehicle manufacturer. 17 6.0 Using Car Seat WITH Built-in Harness 6.1 Positioning the Harness Straps FAILURE TO PROPERLY ADJUST THE HARNESS STRAPS FOR YOUR CHILD INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. Snugly adjust the belts provided with this child restraint around your child. 1. Open harness clip . 2. Unbuckle harness straps . 3. Place child in the seat. 18 4. Check the crotch strap. Choose the position that is closest to but not under your child. To move the strap: Reach under seat and push metal retainer up through the slot sideways . Place the retainer in the appropriate slot. Pull on buckle to make sure it is secure. 5. The harness straps must go into the slots even with or just above the shoulders . 6. If straps are in the proper slots, go to step 11 on page 21. 7. To adjust harness straps: Remove straps from harness plate and adjuster bar . 19 8. Pull strap ends through slots and reinsert them in the correct slots . as determined in step 5. 9. Reassemble straps onto adjuster bar exactly as shown . There must be some strap extended below the adjustment bar. 10. Push adjuster bar down . 11. Rotate red lock down . 20 11. Check that the straps are inserted at the same level and that they are not twisted. From the front of the seat, pull on harness to make sure it is secure. 12. Harness Adjustment Remove child from car seat. From behind the seat move the red lock up, lift adjuster bar and lengthen or shorten the straps as needed. (See also Section 6.3, Securing Your Child in the Car Seat, page 26.) REMEMBER to check the shoulder and crotch straps as your child grows and move them to the next position when necessary. 21 6.2 Securing the Car Seat in Your Vehicle FAILURE TO PROPERLY SECURE THE CAR SEAT IN THE VEHICLE INCREASES THE CHILD’S RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. Carefully follow these instructions and those in your vehicle owner’s manual to be sure your car seat is properly located, positioned, and held tightly at all times. 6.2.1 With a Ve...
Ce manuel est également adapté pour les modèles :Sièges d'auto - 8490 (965.92 kb)