|
Instructions Metra Electronics, Modèle 99-7878B
Fabricant : Metra Electronics Taille : 351.57 kb Nom Fichier : INST99-7878B.pdf
Langue d'enseignement:
|
|
|
|
Aller à la télécharger
Facilité d'utilisation
. . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 3 -DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4 -ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 -Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6 Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWEREnhanceyour installation and fabrication skillsbyenrolling inthe most recognized andrespected mobile electronics school in our industry. Log onto call 800-354-6782 formore information and take stepstoward abetter tomorrow. 95-7878B DASH DISASSEMBLY 95-7878B DASH DISASSEMBLY HONDA INSIGHT 2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the pocket/accessory socket panel below the factory radio. (Figure A) 3 Remove (1) 8 MM bolt facing up behind panel. Figure B) 4 Open the glove box then use a small blunt tool (ie: the wooden handle of a hammer) to put pressure on the back B of the radio chassis to unclip and remove the radio. (Figure C) POWEROUTLETOFFREARFRONTAUTOPUSH Continued on page 2. OFFREARFRONTAUTOPUSH C 1 95-7878B DASH DISASSEMBLY 95-7878B DASH DISASSEMBLY HONDA INSIGHT 2010 5 Remove (2) Phillips screws securing the hazard switch to the back of the factory radio panel. (Figure D) 6 Remove (2) Phillips screws securing the air bag light to the back of the factory radio panel. (Figure D) 7 Remove the (8) retaining clips from the factory radio panel. (Figure D) Continue to kit preparartion. D HAZARDSWITCHTWOSCREWSAIR BAGSWITCHTWOSCREWS8RETAINING CLIPS 2 99-7878B KIT PREPARATION KIT PREPARATION 1 Secure the hazard switch into the radio housing panel using the factory hardware. (Figure A) 2 Secure the air bag light into the radio housing panel using the factory hardware. (Figure A) 3 Attach the (8) retaining clips to the radio housing panel in the same location as removed from the factory radio panel. (Figure A) Continue to kit assembly. A HAZARDSWITCHTWOSCREWSAIR BAGSWITCHTWOSCREWS8RETAINING CLIPS 3 99-7878B KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) A 3 Snap the pocket into the bottom B opening of the radio housing. (Figure B) 4 Slide the aftermarket head unit into the cage and secure. (Figure C) 5 Reassemble dash in reverse order of disassembly. C 4 99-7878B KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) A 3 Snap the pocket into the bottom B opening of the radio housing. (Figure B) 4 Slide the head unit into the radio opening until the side clips engage. (Figure C) 5 Snap the Trim plate into the Radio Housing. (Figure C) 6 Reassemble dash in reverse order of disassembly. C 5 99-7878B KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing. (Figure A) 3 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure B) 4 Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio. (Figure C) 5 Snap the Double DIN trim plate into the Radio Housing. (Figure C) 6 Reassemble dash in reverse order of disassembly. 1-800-221-0932 B C REV. 07/15/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST99-7878B ...
Écrivez votre propre critique du dispositif
|
|