Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Installation Manual 1 pc. Owner's guide 1 pc. INSTALLATION PARTS ACCESSORIES MAIN UNIT 1 PACKING LIST Changer Mounting Angle Adjustment Tool 1 pc. Hex Head Bolt with Washer Base (M5 x 12) 4 pcs. 5 Meter Din Cable 1 pc. Screw Hole Cover Labels 1 pc. Mounting Bracket 2 pcs. Phillips Head Screw 4 pcs. 6 COMPACT ACC-30 DIGITAL AUDIO 6 DISC COMPACT DISC CHANGER BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the 4 transport screws. Be sure to remove the screws prior to installation. Retain these screws for future use when transporting the unit for service/maintenance. l Caution . After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Precautions To prevent a short-circuit, 1 l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation. l Connect power wires last. Note If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation, not to cause a short circuit. Do not install the unit in the following locations. 2 l Locations exposed to direct sunlight. l Where hot air is discharged from the car heater. l In areas subject to extreme temperatures. Incorrect installation can cause the sound to "skip" when playing a disc. 3 Mount the unit firmly in place, using the supplied brackets and screws. Be careful not to damage the car wiring. 4 l Be sure to use the supplied screws. 5 l Be careful not to snag any wires when tightening screws. l Do not use any of the screws that are part of the brake or steering system, to install the unit. . This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning 6 of the mechanism. INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON Set the anti-vibration springs to Set the anti-vibration springs to position "H". position "V". position "H" position "V" 45° ANGLE INSTALLATION Set the anti-vibration springs to position "45°". position "45°" H45° V H 45°V H45°V 45° PROCEDURE FOR HORIZONTAL INSTALLATION Drill holes 1/8" (4mm) in diameter. 1 2 3 Bracket Attach a mounting bracket to each side of the unit, using the 4 hex head bolts with washer base. Determine the mounting location, and drill four mounting holes. Secure the unit in place, using four self-tapping Phillips head screws. Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Self-tapping Phillips head screw Never mount the unit near the fuel tank. Bracket Bracket Bracket Hex head bolt with washer base NOTE: Make sure anti-vibration springs are set to position "H". H45° V NOTE: If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from catching on carpet. Cut holes in carpet before drilling into sub-surface. PROCEDURE FOR VERTICAL INSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Hex head bolt with washer base Bracket Bracket 4 2 Attach a mounting bracket to each side of the unit, using the hex head bolts with washer base. Mount the unit in place, using four self-tapping Phillips head screws. Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Set the anti-vibration springs to position "V". Determine the mounting location, and drill four mounting holes. 3 1 Never mount the unit near the fuel tank. Drill holes 1/8" (4mm) in diameter position "V" Self-tapping Phillips head screw Bracket Bracket H 45°V NOTE: If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from catching on carpet. Cut holes in carpet before drilling into sub-surface. PROCEDURE FOR 45° ANGLE INSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. 4 2 Attach a mounting bracket to each side of the unit, using the 4 hex head bolts with washer base. Mount the unit in place, using four self-tapping Phillips head screws. Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion. Set the anti-vibration springs to position "45°". Determine the mounting location, and drill four mounting holes. 3 1 Never mount the unit near the fue...