Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions Kenwood, Modèle KDC-2027SA(SG)

Fabricant : Kenwood
Taille : 3.55 mb
Nom Fichier :
Langue d'enseignement: ruplenhuskcs
Aller à la télécharger



Facilité d'utilisation


. No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? The sound quality . One of the speaker . Check the speaker wiring. . The speakers are not wired . Reconnect the speaker wires connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on ? There’s a source you can’t switch. (page 14). . There’s no CD inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on (page 14) . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on (page 14) . ? Even if Loudness is turned ON, high-pitched tone isn't compensated for. . Tuner source is selected. . High-pitched tone isn't compensated for when in Tuner source. ? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on (page 14). — 17 — English English Disc source ? The specified disc does but another one plays . The specified CD is quite . Clean the CD. . The CD is upside-down. . Load the CD with the labeled side . The disc is severely scratched. . Try another disc instead. ? The specified track will not play. . Random play has been selected. . Turn off random play. ? Track repeat, track scan, and random play start by themselves. . The setting is not canceled. . The settings for these functions remain on until the setting or the disc ejected, even if the power is turned off or the source changed. ? Cannot play CD-R or CD-RW. . Finalization processing is not being conducted for CD-R/CD-RW. . Conduct finalization processing with CD recorder. ? A CD ejects as soon as it is loaded. . The CD is upside-down. . Load the CD with the labeled side up. . The CD is quite dirty. . Clean the CD, referring to the section on (page 5). ? Can’t remove disc. . The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. . The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. ? The disc won’t insert. . There’s already another disc inserted. . Press the [ 0] button and remove the disc. ? Track Search can't . For the albums first . For each album, Track Search can't be done direction for the first song song. The messages shown below condition. E-04: The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. . Clean the CD and load it correctly. IN (Blink): The CD player section is not operating properly. . Reinsert the CD. If the CD cannot be ejected or display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. — 18 — Specifications Specifications FM tuner section Frequency range (50 ..............87.5 MHz – 108.0 Usable sensitivity (S/N = ................................. 0.7 .V/75 . Quieting Sensitivity (S/N = .............................. 1.6 .V/75 . Frequency response ( ± 3 dB) .................................30 Hz – Signal to Noise ratio (MONO) ..............................................65 Selectivity (DIN) ( ± 400 kHz) .............................................. . 80 dB Stereo separation (1 kHz) ....................................................35 dB MW tuner section Frequency range (9 kHz space) .....................531 kHz – 1611 kHz Usable sensitivity (S/N = 20dB) ........................................... 25 .V LW tuner section Frequency range .............................................153 kHz – 281 kHz Usable sensitivity (S/N = 20dB) ........................................... 45 .V CD player section Laser diode .......................................................................GaAlAs Digital filter (D/A) ......................................8 Times Over Sampling D/A Converter .......................................................................1 Bit Spindle speed...............................................500 – 200...

Ce manuel est également adapté pour les modèles :
Unité - KDC-2027 (3.55 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories