Instructions Kenwood, Modèle KRC-694
Fabricant : Kenwood Taille : 4.44 mb Nom Fichier :
Aller à la télécharger
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on . . The cassette tape is bad. . Try playing another cassette tape. If works fine, the first tape was bad. . The values of Volume offset are low. . Turn up the Volume offset, referring to the section on (page 6). ? The sound quality is poor or distorted. . One of the speaker wires is being pinched by a screw in the car. . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output terminal is connected to a different speaker. ? Even though Synchronize Clock is ON, the clock can’t be adjusted. . The received RDS station isn’t sending time data. . Receive another RDS station. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on . — 31 — English English Cassette tape source ? Can’t remove tape. . The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. . The tape can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. ? The DPSS and Music Repeat don’t operate correctly. . The space between the songs on the tape can’t be recognized because it’s too short. . Have at least 4 seconds between songs. . The space between songs can’t be recognized because there’s too much noise between songs. . Reduce the noise between songs. ? The blank skip doesn’t work. . Because noise is too loud, the non-recorded part can’t be recognized. . Reduce the noise between songs. ? Blank Skip functions at places that are recorded. . Because the recording level is low, it’s recognized as not recorded. . Turn Blank Skip OFF. ? (page 16) is cancelled arbitrarily. . The power was turned OFF or a source selection or other was performed. . Music repeat is cancelled when the power is turned source selection or other operation is performed. Disc source ? "AUX1" is displayed without achieving External disc control mode. . Unsupported disc changer is connected. . Use the disc changer mentioned in the IMPORTANT INFORMATION of the section on (page 3). ? The specified disc does not play, but another one plays instead. . The specified CD is quite dirty. . Clean the CD. . The disc is loaded in a different slot from that specified. . Eject the disc magazine and check the number for the specified disc. . The disc is severely scratched. . Try another disc instead. If the following situations, consult your nearest service center: Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX1" showing in the display during the Changer Mode. — 32 — The messages shown below display your systems The messages shown below display your systems EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. . Load the disc magazine properly. No CD in the unit. . Insert the CD. No Disc/ NO DISC: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. TOC Error/ TOC ER: No disc has been loaded in the disc magazine. . Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. . Clean the CD and load it correctly. E-05: The CD is upside-down. . Load the CD correctly. Blank Disc/ BLANK: Nothing has been recorded on the MD. No Track/ NO TRACK: No tracks are recorded on the MD, although it has a title. E-15: Media was played that doesn’t have data recorded that the unit can play. . Use media that has data recorded that the unit No Panel/ NO PANEL: The faceplate of the slave unit being connected has been removed. . Replace it. E-77: The unit is malfunctioning for . Press the reset button on the not disappear, consult your nearest service Mecha Error/ MECHA ER: Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. . Check the disc magazine. And then press the reset button on the unit. If the "Mecha Error"/ "MECHA ER" code does not disappear, consult your nearest service center. Hold Error/ HOLD ER: The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation. . Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc will start playing again. NO NAME: Attempted to display DNPS during the CD play having no disc names prese...
Ce manuel est également adapté pour les modèles :
Unité - KRC-594(V) (4.44 mb)
Unité - KRC-594 (4.44 mb)
Écrivez votre propre critique du dispositif
)
