Évaluations - 5, GPA: 4
(
)
)
|
Photos et spécifications Pioneer DEH-3300UB |
Facilité d'utilisation
Ground cables for this unit and other equipment (especially, high-current products such as power amps) must be wired separately. If they are not, an accidental detachment may result in a fire or malfunction. This unit 12 34 5 1 Power cord input 2 Rear output or subwoofer output 3 Antenna input 4 Fuse (10 A) 5 Wired remote input Hard-wired remote control adaptor can be connected (sold separately). En Section Section 03 Installation Installation b Blue/white 2 Secure the mounting sleeve by using a Power cord Installation Connect to auto-antenna relay control term- screwdriver to bend the metal tabs (90°) 03 English Important inal (max. 300 mA 12 V DC). into place. 1 3 3 2 4 4 5 5 6 6 b 8 9 7 a e d c The pin position of the ISO connector will dif c Yellow/black ! Check all connections and systems before If you use an equipment with Mute function, final installation. wire this lead to the Audio Mute lead on that ! Do not use unauthorized parts as this may equipment. If not, keep the Audio Mute lead cause malfunctions. free of any connections. ! Consult your dealer if installation requires drild Speaker leads ling of holes or other modifications to the vehi- White: Front left + cle. White/black: Front left * ! Do not install this unit where: Gray: Front right + — it may interfere with operation of the vehi 1 2 Gray/black: Front right * cle. 1 Dashboard Green: Rear left + or subwoofer + — it may cause injury to a passenger as a re2 Mounting sleeve Green/black: Rear left * or subwoofer * Violet: Rear right + or subwoofer + ! sult of a sudden stop. The semiconductor laser will be damaged if it 3 Install the unit as illustrated. Violet/black: Rear right * or subwoofer * overheats. Install this unit away from hot e ISO connector places such as near the heater outlet. In some vehicles, the ISO connector may be ! Optimum performance is obtained when the divided into two. In this case, be sure to con-unit is installed at an angle of less than 60°. nect to both connectors. 60° Notes 1 To power cord input 2 Depending on the kind of vehicle, the function of 3 and 5 may be different. In this case, be sure to connect 4 to 5 and 6 to 3. 3 Yellow Back-up (or accessory) 4 Yellow Connect to the constant 12 V supply terminal. 5 Red Accessory (or back-up) 6 Red Connect to terminal controlled by ignition switch (12 V DC). 7 Connect leads of the same color to each other. 8 Black (chassis ground) 9 Blue/white ! Change the initial setting of this unit. Refer to SW CONTROL (rear output and subwoofer setting) on page 12. The subwoofer output of this unit is monaural. ! When using a subwoofer of 70 W (2 .), be sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/black leads. Power amp (sold separately) Perform these connections when using the optional amplifier. 3 1 DIN front/rear mount This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when installing. DIN Front-mount 1 Insert the mounting sleeve into the dashboard. For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came 5 1 2 3 4 1 Nut 2 Firewall or metal support 3 Metal strap 4 Screw 5 Screw (M4 . 8) # Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions. DIN Rear-mount 1 Determine the appropriate position where the holes on the bracket and the . . . . 2 4 with the vehicle. fer depending on the type of vehicle. Connect side of the unit match. 5 5 9 and b when Pin 5 is an antenna control type. In another type of vehicle, never connect 9 and b. 1 System remote control a Blue/white Connect to Blue/white cable. Connect to system control terminal of the 2 Power amp (sold separately) power amp (max. 300 mA 12 V DC). 3 Connect with RCA cable (sold separately) 4 To Rear output or subwoofer output 5 Rear speaker or subwoofer 16 17 En En Section 03 Installation 2 Tighten two screws on each side. For details, refer to Removing the front panel to protect your unit from theft and Re-attaching the front panel on page 5. 2 3 1 1 Tapping screw (5 mm . 8 mm) 2 Mounting bracket 3 Dashboard or console Removing the unit 1 Remove the trim ring. 1 Trim ring 2 Notched tab ! Releasing the front panel allows easier ac cess to the trim ring. ! When reattaching the trim ring, point the side with the notched tab down. 2 Insert the supplied extraction keys into both sides of the unit until they click into place. 3 Pull the unit out of the dashboard. Removing and re-attaching the front panel You can remove the front panel to protect your unit from theft. Press the detach button and push the front panel upward and pull it toward you. En Appendix Additional Information Troubleshooting Symptom Cause Action The display You did not per-Perform operation automatically form any opera-again. returns to the tion within about ordinary dis-3...
Ce manuel est également adapté pour les modèles :Unité - DEH-4300UB (2.2 mb)