Évaluations - 2, GPA: 3.5 ( )

Fabricant : Kenwood Taille : 475.88 kb Nom Fichier : Langue d'enseignement:

2 CAUTION If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those cables to the power source running through the fuse box. 2 WARNING Ignition cable (Red) Battery cable (Yellow) Ground cable (Black) - (To car chassis) Ignition key switch Car fuse (Main fuse) ACC Car fuse box Battery Power control/ Motor antenna control cable (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. If no connections are made, do not cut the tube off from the edge of the cable. ISO connector unsupported car (KRC-477R/377R/32R only) n Power Control terminal (P31) Plug (P.32) KENWOOD disc changer / DAB control input NOTE To connect the Disc changer or DAB unit, consult each manual. NOTE To connect the KENWOOD navigation system, consult your navigation manual. To front left speaker – + To front right speaker – + To rear left – box speaker To rear right speaker + – + — 30 — n ISO connector supported car Antenna Conversion FRONT Plug (P.32) To connect the Disc changer or DAB unit, consult each manual. NOTE KENWOOD disc changer / DAB control inputRear right output (Red) FM/AM antenna Fuse (10A) Front left output (White) (KRC-477R/477RV only) Front right output (Red) (KRC-477R/477RV only) Rear left output (White) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Antenna Cord (ISO) To Power Control terminal Car’s wiring harness Special antenna cable (Commercially available) For Volkswagen car Power Control terminal (P31) input TEL mute terminal n Power Control Terminal Connections The output of the the power on/off switching This terminal can be terminal of the amplifier, special antenna cable for Antenna Cord (ISO) Power Control terminal (Flat terminal) Power Amplifier Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Power control cable Special antenna cable (For Volkswagen car) (Commercially available) NOTE To connect the KENWOOD navigation system, consult your navigation manual. — 31 — English Connecting n Connector Function Guide n Plug Setting 2 WARNING Connecting the 10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 10 Connector A Connector B The pin arrangement of vehicle you drive. prevent damage to the 1 The A-7 pin (red) of the vehicle's the ignition, and the A-4 pin (yellow) constant power supply. (Default setting; Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 A–5 A–7 A–8 Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Yellow Red Blue/White Red Yellow Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black *Plug setting Battery Ignition (ACC) Power Control Ignition (ACC) Battery Earth (Ground) Connection Rear Right ( + ) Rear Right ( – ) Front Right ( + ) Front Right ( – ) Front Left ( + ) Front Left ( – ) Rear Left ( + ) Rear Left ( – ) 1 2 1 2 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. (Default setting; KRC-477RV) 10 *Plug setting: See right side. — 32 — Installation n Installation Firewall or metal support screw Bend the tabs of the mounting sleeve (commercially with a screwdriver or similar utensil available) and attach it in place. Metal mounting strap (commercially available) Self-tapping Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). — 33 — Installation English ¦ Removing the hard rubber frame 1 Engage the catch locks on the lower level. Lower the frame and pull Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. NOTE Removing the Unit n Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch pins on the removal tool. Catch facing up Refer to the section then remove the hard Remove the screw (M4 . 8) on the back panel. Insert the two removal tools as shown. 3 2 1 Screw (M4X8) (commercially available) 2 CAUTION — 34 — Troubleshooting What might calling service, PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn The fuse has blown. After checking for short circuits fuse with one having the same No ACC position on vehicle ignition. Connect the same cable to the ignition No sound can be heard, or the The Attenuator function is turned on. Turn off the Attenuator function. volume is low. The fader and/or balance settings are set all Reset the fader and/or balance settings. one side. The input/output cables or wiring harness are connected Reconnect the input/...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :