Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
The unit may be damaged or fail to work share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the connect the connectors either to both the front output or to both the rear output terminals (do not mix For example, if you connect the + connector of the left speaker to a front output terminal, do not connect - connector to a rear output terminal. • After the unit is installed, check whether blinkers, wipers, etc. on the car are — 16 — Connecting Wires to Terminals Connecting Wires to Terminals Rear left output (White) ANT. CONT. P.CONT ILLUMI TEL MUTE FRONT • L FRONT • R REAR • L REAR • R – + FM/AM antenna input Rear right output (Red) Fuse (10A) Wiring harness (Accessory1) White/Black Gray/Black Purple/Black White Gray Green Purple To front left speaker To front right speaker To rear right speaker To rear left speaker Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch10 Car fuse box (Main fuse) ACC Car fuse box If no connections are made, do not let the wire come out from the tab. Front left output (White) (KRC-569 only) Front right output (Red) (KRC-569 only) To connect the Disc changer, consult your Disc changer manual. Green/Black Power control wire (Blue/White) Motor antenna control wire (Blue) When using the optional power amplifier, connect to its power control terminal. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. Not UsedDo not let the wire come out from the tab. Battery — 17 — Installation Installation ¦ Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (for example, the sound may Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in Japanese-Made Cars 1 Refer to the section "Removing the hard rubber frame" (page 19) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 Never insert the taptite screw . 16 mm) in any other screw than the one specified. and may cause damage — 18 — ¦ ¦ 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 19 — English English What might seem to be a malfunction in your unit may ? The sound quality is poor or distorted. just be the result of slight misoperation or miswiring. . One of the speaker wires is being pinched by a screw in the car. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery wire. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is tur...
Ce manuel est également adapté pour les modèles :Unité - KRC-369 (381.83 kb)
Unité - KRC-469 (381.83 kb)