Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
Display and setting: "LPF NF" : 50 Hz / 80 Hz / 120 Hz / Through Volume Offset Set the sound level of the each source selected the level difference between the basic sound required level. Display and setting: "V Offset"/"VOL Offset" : - 8 – ±0 — 15 — You can choose from three tuning modes: auto seek, preset station seek, and manual. The AUTO 1 indicator lights up when auto seek tuning is selected, and the AUTO 2 indicator lights when preset station seek tuning is selected. Selecting Tuning Mode: Press the AUTO button. Each time you press the AUTO button, the mode switches as follows. Tuning: Press the SRC (source) button repeatedly to select the tuner mode. "TUNER" is displayed when the tuner mode has been selected. Press either the FM or AM button to select the band. Each time you press the FM button, the band switches between the FM1, FM2 and FM3 (which are used for groups of preset stations). Press the AM button to select the AM band. • Auto Seek Tuning Press the .button to seek higher frequencies. Press the 4 button to seek lower frequencies. • Preset station seek tuning Press the .button to move to the next preset station (i.e., the one with the next highest number), and the 4button to move to the last preset station (i.e., the one with the next lowest number). • Manual Tuning Press the .button to increase the frequency by one step. Press the 4button to decrease the frequency by one step. The ST indicator lights up when stereo broadcasts are being NOTE 3 2 1 Auto 1 (Auto Seek Tuning) Auto 2 (Preset Station Seek Tuning) Manual (Manual Tuning) Tuning Tuner features — 16 — English AUTO/ AM AME FM 4 . DISP/NAME.S 38 SRC #1-6 KDC-X617/KDC-516S/KDC-57MR KDC-V6017 AUTO indicator ST indicator AUTO indicator ST indicator Band display Frequency Preset station number Band display Frequency Preset station number received . Recalling a Preset Press the preset The number of the NOTE Direct Access Tuning ( Function of remote) When you know the frequency listen to, you can input it directly 1 Select the band by pressing the FM 2 Press the DIRECT button. "----" is displayed for 10 seconds. If you make no input in the 10-second period, tuning is automatically canceled. 3 Enter the frequency of the desired station. If you want to listen to an FM station at 92.1 MHz, for example, press 0, 9, 2, and 1. If you want to listen to an AM station at 810 kHz, for example, press 0, 8, 1, and 0. NOTE • You cannot enter frequencies above or below what a band can receive. • FM frequencies can only be input in 0.1 MHz steps, and not 0.01 MHz steps. Canceling Direct Access Tuning: Press the DIRECT button again. You can store six stations AM bands. Auto Memory Entry You can automatically store all the receivable the band currently being listened to, and then the touch of a button later. This function is especially when you are travelling and do not know what available. Up to six frequencies can be stored this 1 Select the band for auto memory entry. 2 Press the AME button for at least two seconds to start auto memory entry. The numbers of the preset station buttons are shown in order. When all the stations in a certain band are stored in the preset memory, the auto memory entry stops. The tuner then plays the last station received. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. Station Preset Memory Store the frequency of a station. You can then recall that station with a single touch of a button. 1 Select the band/station that you want to have stored. 2 Press the button (#1-6) that you want to use for the station, for at least two seconds. The button number blinks once in the display to indicate that the data has been stored. — 17 — Tuner features Station Name English You can assign names Memory. Up to 32 FM assigned names. 1 Adjust the frequency to the enter. 2 Press the NAME.S button for at least "NAME SET" is displayed once the station is entered. The cursor will blink in the position where 3 Press either the 4 or . button to move the cursor to the desired position. The 4 button moves the cursor to the left, and the . button to the right. You can also move the cursor left or right by pressing 4 or . buttons, respectively, on the remote. 4 Each time the 38 button is pressed, the characters to be entered change as listed below. Press the FM or AM button to display the desired character. Characters that can be displayed are as follows. Alphabet (upper case): A ~ Z Alphabet (lower case): a ~ z Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ] Special characters: aaeeiioouuNC®.‹ fl aaeeiioouunc©.› fi NOTE Direct Alphabet Input (Function of remote with number/letter entry buttons) Direct input can be made of letters (alphabetical) with the letter entry buttons on the remote. Example: Use the following table to enter the name "DANCE" . Character Button to press # Times pressed “ D” #3 1 “ A” #2 1 “ N” #6 2 “ C” #2 3 “ E” #3 2 5 Cont...
Ce manuel est également adapté pour les modèles :Unité - KDC-57MR (682.3 kb)
Unité - KDC-V6017 (682.3 kb)
Unité - KDC-X617 (682.3 kb)