• WOW can be set when SRS WOW or User memory is selected at (page 12). • * This mode is available only when (page 12) is ON. • The Loudness can not be set when SRS WOW is selected at (page 12). — 13 — General features General features 1st section [2] button Adjustment Item Bass Center Frequency Bass level Bass Q Factor Bass Extend Display "Bass FRQ" "Bass" "Bass Q" "Bass EXT" Range 60/70/80/100 or 150 Hz –8 — +8 1.00/1.25/1.50/2.00 ON/OFF [3] button Adjustment Item Middle Center Frequency Middle level Middle Q Factor Display "MID FRQ"/"Middle FRQ" "MID"/"Middle" "MID Q"/"Middle Q" Range 0.5/1.0/1.5/2.0 kHz –8 — +8 1.0/2.0 [4] button Adjustment Item Treble Center Frequency Display "TRE FRQ"/"Treble FRQ" Range 10.0/12.5/15.0/17.5 kHz Treble level "TRE"/"Treble" –8 — +8 [5] button Adjustment Item Balance Fader Display "Balance" "Fader" Range Left 15 — Right 15 Rear 15 — Front 15 • According to the Bass Q Factor setting value, the frequencies that can be set in Bass Center Frequency change as shown below. Bass Q Factor Bass Center Frequency 1.00/1.25/1.50 60/70/80/100 2.00 60/70/80/150 • When the bass extend is set to ON, low frequency response is extended by 20%. 2nd section [2] button Adjustment Item Display Range Front High Pass Filter "HPF Front" Through/40/60/80/100/ 120/150/180/220 Hz Rear High Pass Filter "HPF Rear" Through/40/60/80/100/ 120/150/180/220 Hz [3] button Adjustment Item Display Range Non-Fading "LPF NF" 50/80/120/Through Hz Low Pass Filter [4] button Adjustment Item Display Range Loudness "Loudness" ON/OFF [5] button Adjustment Item Display Range WOW "SRS WOW" Low/High/OFF TruBass "SRS TruBass" ON/OFF FOCUS "FOCUS" Low/High/OFF SRS "SRS" ON/OFF — 14 — Loudness: Compensating for low and high tones during low volume. • WOW: TruBass, FOCUS and SRS are all set to values shown below. WOW TruBass FOCUS SRS High ON High ON Low ON Low ON OFF OFF OFF OFF • TruBass: Assisting the playback for the super bass sound. • FOCUS: Adjusts the sound image by changing the vertical position of the speakers virtually. • SRS: Making a natural 3D sound field. • SRS cannot be set in tuner source. 3rd section [2] button Adjustment Item Display Range Volume offset "Volume Offset" –8 — ±0 [3] button Adjustment Item Display Range Non-Fading level "NF Level" –15 — +15 Non-Fading Phase "NF Phase" Normal (0°)/Reverse (180° ) Volume offset: Each source's volume can be set from the basic volume. — 15 — General features General features Display Mode Switching Switching the display mode. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "DISP" is displayed above the [3] button. Refer to (page 8) . 2 Enter display control mode Press the [3] ("DISP") button. 3 Select the display mode Press the [2] ("MODE") button. Each time the button is pressed the display mode switches as shown below. KDC-PSW9524 Display Mode Display "Display:A" Left side graphic part Upper text display part Lower text display part Function display "Display:B" Left side Right side graphic part graphic part Function display "Display:C" KDC-8024 Display Mode Display "Display Type A" Indicator display Upper text display part Lower text display part Function display "Display Type B" Graphic part Function display "Display Type C" Graphic part Spectrum analyzer& Text display part 4 Exit display control mode Press the [RTN] button. • If the [1] — [6] button or the [NEXT] button is pressed while "Display Type C" is selected, "Display Type C" is temporarily switched to "Display Type B" and the function item is displayed. After the operation is completed, "Display B" is returned to "Display Type C". • If (page 26) B" or "Display Type C" is selected, the display switched to "Display Type A". Right side graphic side graphic part — 16 — Function of the KDC-PSW9524 Function of the KDC-PSW9524 • The setting of this function is available while "Display Type B" or Right Side Graphic Display Switching Switching the Right side graphic Display. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "DISP" is displayed above the [3] button. Refer to (page 8) . 2 Enter display control mode Press the [3] ("DISP") button. 3 Select the Right side graphic display Press the [3] ("SA") button. Each time the button is pressed the right side graphic display switches as shown below. Right side graphic display Demonstration Movie 1 Movie 2 Movie 3 Downloaded movie Spectrum analyzer 1 Spectrum analyzer 2 Spectrum analyzer 3 Spectrum analyzer 4 Spectrum analyzer 5 Wallpaper 4 Exit display control mode Press the [RTN] button. "Display Type C" is selected for the Display mode. • A downloaded movie can be selected when it has been downloaded into this unit. Refer to (page 50). • Wallpapers can be changed. This unit comes with 3 types of wallpaper registered. A do...
)
