Using this setting can save the vehicle's battery power. Display Setting "OFF – – –" Power OFF Timer function is OFF. "OFF 20MIN"/ "OFF 20M" Turns the power OFF after 20 minutes. (Original setting) "OFF 40MIN"/ "OFF 40M" Turns the power OFF after 40 minutes. "OFF 60MIN"/ "OFF 60M" Turns the power OFF after 60 minutes. This setting is done after setting (page 24). Function of the CD Read Setting When there is a problem this setting play the CD Display Setting "CD READ 1" Play CD and MP3. "CD READ 2" Play CD by force. Setting "CD READ 2" cannot play MP3. Some music CDs may not be played back even in mode. — 29 — English English External view External view ......... Number of ......... Number of 1 4 ......... 1 ......... 1 .........2 5 2 ......... 1 3 .........1 6 ......... 2 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button. 2CAUTION • If your car is not prepared consult your Kenwood • Only use antenna conversion antenna cord has an ISO • Make sure that all wire connections inserting jacks until they lock • If your vehicle's ignition does not ignition wire is connected to a power voltage such as a battery wire, the power the ignition (i.e., it will not turn on and off ignition). If you want to link the unit's power connect the ignition wire to a power source on and off with the ignition key. • If the fuse blows, first make sure that the wires a short circuit, then replace the old fuse with one with rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. — 30 — Connecting Connecting To Steering remote (KDC-5024/5024V/507 only) To External Display/ Steering remote (KDC-M6024G/M6024/V6524/6024 only) Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 Yellow Battery A–5 Blue/White Power Control A–6 Orange/White Dimmer A–7 Red Ignition (ACC) A–8 Black Earth (Ground) Connection Speaker Connector B–1 Purple Rear Right ( + ) B–2 Purple/Black Rear Right ( – ) B–3 Gray Front Right ( + ) B–4 Gray/Black Front Right ( – ) B–5 White Front Left ( + ) B–6 White/Black Front Left ( – ) B–7 Green Rear Left ( + ) B–8 Green/Black Rear Left ( – ) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TEL MUTE P.CONT ANT.CONT FRONT REMO.CONT — 31 — Rear rightoutput (Red) /Non-fading right output (KDC-M6024G/ M6024/ V6524/ 6024 only) (Red) Front left output (White) (KDC-M6024G/M6024/V6524/Rear left output (White) Non-fading left output (KDC-M6024G/ M6024/ V6524/ 6024 only) (White) (KDC-M6024G/M6024/KENWOOD disc changer input Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) To connect the Disc changer, consult your Disc changer manual. Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) control terminal when using or to the antenna control terminal in the vehicle. Connect to the terminal that is grounded when either the telephone rings or during conversation. A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) See page 32 To connect the KENWOOD navigation system, consult your navigation manual. Connect either to the power the optional power amplifier, Connecting Connecting 2WARNING Connecting the ISO The pin arrangement vehicle you drive. Make prevent damage to the unit. The default connection for the 1 below. If the ISO connector pins are set 2 or 3, make the connection as illustrated. Please be sure to reconnect the 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of...
)
