Select the "Clock Adjust"/ "CLK ADJ" display. 2 Enter Clock Adjust mode Press the [ 4] or [ . ] button for at least 1 second. The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit Clock adjustment mode Press the [MENU] button. Function of the KDC-5023R Synchronize Clock Synchronizing the RDS station time data and this unit's clock. Display Setting "SYNC ON" Synchronizes the time. "SYNC OFF" Adjust the time manually. It takes 3 to 4 minutes to synchronize the clock. DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF. Function of the KDC-MPV7023/ Selectable Illumination Selecting the button illumination Display Setting "Button Green"/ "KEY GRN" The illumination color is green. "Button Red"/ "KEY RED" The illumination color is red. Switching Display Type Setting the Display type. Display Setting "Display C"/ "DISP C" Demonstration. "Display A"/ "DISP A" Normal display type. "Display B"/ "DISP B" Silent display type. Function of the KDC-MPV7023 Illumination Color Setting You can set the display to a desired color. 1 Select Illumination Color Setting Mode Press the [FM] or [AM] button. Select the "COL" display. 2 The color continues to change gradually Hold down on the [ 4] or [ . ] button. Release your finger at the color you want. Colors adjusted using either [ 4] or [ . ] will be stored automatically, and they can be called by pressing [5] button. — 26 — Quick call up the Quick call up the Press the desired Button Color Dimmer Dimming this unit's display [1] [2] [3] [4] Silky White Red Blue Blue Green Selecting the Color mode Press the [6] button. Each time the button is pressed the Color mode shown below. switch is turned ON. Display "Dimmer ON" "Dimmer OFF" Setting The display dims. The display doesn't dim. Function of the KDC-MPV7023/KDC-6023 Switching preout Display Color mode "Scan" The color changes in sequence. "SRC" The color changes according to the selected source. "Time" The color changes every 6 hours. Keeps the presently set color. Blue fine adjustment 1Press the [3] button for at least 2 seconds. Switching the preout between the rear and non-fading it outputs without effect from the fader control.) Display Setting "SWPRE Rear" Rear preout. "SWPRE N-Fad" Non-fading preout. Function of the KDC-MPV7023/KDC-6023 2Press the [ 4] or [ . ] button. When the blue fine adjustment is completed, press the [3] button. Dual Zone System Makes the sound different for the front channel and rear channel. Display Setting "Zone 2 OFF" The front and rear are the same source sound. Contrast Adjustment Adjusting the display contrast. "Zone 2 ON" The front and rear are the different source sound. • When the Dual Zone System is on, there is only sound effect including Audio control for internal source. Display and Setting "Contrast 0"/ "CONT 0" … • When you set the Dual zone system to ON while the non-fading preout is switched ON, the sound of the non-fading preout isn’t "Contrast 5"/ "CONT 5" (Original setting) output. … • When the source is selected to VZ-7000P/N (optional accessory), the VZ-7000P/N sound is not output if the Dual Zone System is "Contrast 10"/ "CONT 7" turned ON. — 27 — English English Function of the for news bulletin Dual Zone System Only stations whose reception is good "Zone 2 Front" The rear is this unit's internal source, and seek tuning. front is selected source sound. Display Setting "LO.S OFF" The local seek function is OFF. Function of the KDC-5023R "LO.S ON" The local seek function is ON. News Bulletin with Timeout Setting It switches automatically when a news bulletin starts even radio isn't being listened to. Also, the time interval when Function of the KDC-5023R interrupt is prohibited can be set. Display and Setting Tuning Mode "NEWS OFF" Sets the tuning mode. Tuning mode Display Operation "NEWS 00M" … Auto seek "AUTO 1" Automatic search for a station. "NEWS 90M" When "NEWS 00M" — "NEWS 90M" is set, the News Bulletin Interrupt function is ON. When it's ON, the "NEWS" indicator is ON. When the news bulletin starts, "NEWS" is displayed, and it switches to the news bulletin. • If you choose the "20M" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. • The news bulletin volume is the same level that was set for (page 17). • This function is only available if the desired station sends PTY-code Preset station seek "AUTO 2" Search in orde...
)
