Instructions Kenwood, Modèle KDC-W707
Fabricant : Kenwood Taille : 1.07 mb Nom Fichier :
Langue d'enseignement:
Aller à la télécharger
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• *2 You can control this item when (page 33) is set to "SWPRE:Sub-W". (KDC-W707 only) • *3 You can control this item when (page 12) is set to "SW ON". • *3 You can control this item when "2Zone" of (page 12) is set to "OFF". • *4 You can adjust these items in detail by the following methods. (Function of the KDC-W808) • *4 Source tone memory: Puts the set up value in the memory per source. (Detail Audio item is included) 5 Exit Audio Control mode Press any button. Press a button other than the [VOL] knob and [ATT]/ [ANG] button. Adjust the detail of Audio Control 1 Select the Audio item to adjust By referring to the step 1 — 3 above, select the desired item to be set in detail from the items marked with *4. 2 Enter Detail adjustment mode of Audio Control Press the [VOL] knob for at least 1 second. 3 Select the Detail Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Adjust the Detail Audio item Turn the [VOL] knob. Bass level Adjustment Item Display Range Bass Center Frequency "Bass Freq" 40/50/60/70/80/100/ 120/150 Hz Bass Q Factor "Bass Q" 1.00/1.25/1.50/2.00 Bass Extend "Bass EXT" ON/OFF Middle level Adjustment Item Display Range Middle Center Frequency "Middle Freq" 0.5/1.0/1.5/2.0 kHz Middle Q Factor "Middle Q" 1.0/2.0 Treble level Adjustment Item Display Range Treble Center Frequency "Treble Freq" 10.0/12.5/15.0/17.5 kHz 5 Exit the Detail Audio Control mode Press the [VOL] knob for at least 1 second. • When you set the Bass Extend to ON, low frequency response is extended by 20%. • You can exit the Audio Control mode at anytime by pressing any button except for [VOL], [ANG] and [ATT] buttons. English | 11 General features Audio Setup Setting the Sound system, such as Cross over Network. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Setup the Audio item Turn the [VOL] knob. Adjustment Item Display Range Front High Pass Filter*2 "HPF-F" Through/40/60/80/100/ 120/150/180/220 Hz Rear High Pass Filter*2 "HPF-R" Through/40/60/80/100/ 120/150/180/220 Hz Low Pass Filter*1,2 "LPF" 50/60/80/100/120/ Through Hz Subwoofer Phase*1,2,3 "SW Phase" Normal (0°)/ Reverse (180°) Volume offset "VOL Offset" –8 — ±0 Loudness "Loudness" ON/OFF Dual Zone System "2Zone" ON/OFF • Volume offset: Sets each source’s volume as a difference from the basic volume. • Loudness: Compensates for low and high tones during low volume. • *1 You can control this item when (page 33) is set to "SWPRE:Sub-W". (KDC-W707 only) • *1 You can control this item when (page 12) is set to "SW ON". • *2 You can control this item when "2Zone" of (page 12) is set to "OFF". • *3 You can control this item when Low Pass Filter is not set to Through. • Dual Zone System Main source and sub source (Auxiliary input) output Front channel and Rear channel separately. -Set up the channel of sub source by (page 34). -Select Main source by [SRC] button. -Adjust the volume of Front channel by [VOL] knob. -Adjust the volume of Rear channel by (page 11). -The Audio Control has no effect on sub source. • You can use the Dual Zone System with the Auxiliary input sources listed below. - Internal auxiliary input (KDC-W808 only) - Option CA-C1AX (KDC-W707 only) 5 Exit Audio Setup mode Press [VOL] knob for at least 1 second. Subwoofer Output Turning the Subwoofer output ON or OFF. Hold down on [AM] of the Control knob for at least 1 second. Each time you press the button, Subwoofer output switches ON and OFF. When it is ON, "SW ON" is displayed. • You can control this function when (page 33) is set to "SWPRE:Sub-W". (KDCW707 only) • You can control this function when "2Zone" of (page 12) is set to "OFF". 12 | English Display Setting Changing the display mode. 1 Enter display Control mode Press the Control knob for at least 1 second. "Display Control" is displayed. 2 Select the Display mode Press the Control knob. Each time you press the knob, the display alternates between the display modes shown in the table below. Display Mode Display "Display Type A" 5 "Display Type B" 54 "Display Type C" 123 1 Upper text display part 2 Middle text display part 3 Lower text display part 4 Text display part 5 Graphic display part • You can display the information that will be shown in the Upper text display part, the Lower text display part or the Level meter display part according to the setting of Display mode. Refer to the following pages for how to select the mode. Display Type A B C Upper 1 —— page 15 Middle 2 —— page 15 Lower 3 —— page 15 Text 4 — page 14 — Gr...
Ce manuel est également adapté pour les modèles :
Unité - KDC-W808 (1.07 mb)
Écrivez votre propre critique du dispositif
)
