Évaluations - 5, GPA: 3.8 ( )

Fabricant : Kenwood Taille : 545.19 kb Nom Fichier : Langue d'enseignement:

Do Not Use • Be sure to use round this unit and do not CDs. Use of special shape the unit to malfunction. • Be sure to use CDs with disc mark only for this unit. • CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW. Do Not Use Labeled Side Do not use the CD with stuck on it. Using such a CD may cause deformed and the sticker to resulting in malfunction of the — 7— General English (KDC-X917/X817/ 5 . FM Description about ANG SRC/ OFF by setting the Lower indicator." Power You can help prevent theft of the faceplate so that the control panel unit, and shutting off the audio. Power ON/OFF: Q DISP CLK AM/ When you turn your vehicle's ignition on, the NF 4 ATT/ also turn on, with the faceplate reversing to show panel. When you turn your vehicle's ignition off, the faceplate KDC-X917/X817/9017 reverse to hide the control panel after a period of time you have set in the "Time setting for removing the faceplate" the menu. The unit's power will turn off. Alternatively, you can remove the faceplate during that period. For details, refer to the "Removing the faceplate" (page 14). PTY LOUD OFF AUD AMEMENU ANG NAME DISP AUTO 5 LOUD indicator NOTE KDC-X717 • When the moving faceplate is hit by an object, it will stop and return to its original state. Remove the object and repeat the action. • The status of the security code function (page 34) is display whenever the power is switched on. "CODE ON" : Security code has been registered "CODE OFF" : Security code has not been registered 2CAUTION Using the Unit in Vehicles with Covered Consoles • Make sure the console is uncovered while the faceplate is reversed. • Do not exert any excess force on the movable parts of the unit, including the faceplate, as it can cause failure in the unit’s mechanism. LOUD indicator — 8— Volume Increasing Volume: Press the button to turn up the volume. Decreasing Volume: Press the button to turn down the volume. Attenuator This function allows you to turn down the volume Turning Attenuator On/Off: Press the ATT button to switch the attenuator on and When the attenuator is off, the volume returns to the original level. NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. Switching Modes Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: Tuner mode CD mode External disc control mode 1 External disc control mode 2 / AUX mode Standby mode Selecting standby Press the SRC button . When "ALL OFF" is The standby mode turns power to the unit on. Use the display illuminated but NOTE • The mode switches to the next mode cannot be used. • The external disc control mode will differ that is connected. • To enable the selection of External disc control mode, you should connect optional switching (which allows you to select both External mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-switching adapter CA-C1AX (which allows you to select mode only). During the AUX mode, "AUX" (or AUX-name display) will show in the display. When the CA-C1AX is being used, the AUX Mode will replace the External Disc Control Mode. NOTE Selecting AUX-name display Pressing the DISP button for at least two seconds during the AUX mode, AUX-name display is blinked for AUX-name selection mode. Pressing 4 or . button during this mode allows you to select "AUX" , "TV" , "VCP" , "GAME" or "PORTABLE" in the AUX mode. The AUX-name selection mode can be exited by pressing the DISP button or doing nothing for 10 seconds. — 9— General English Loudness This function amplifies turned down. The LOUD indicator lights on. Turning Loudness On/Off: Press the LOUD button for at least loudness on and off. NOTE The loudness function does not affect non- System Q You can recall the best audio setting preset for different of the music. Switching the Preset Sound Setting: Each time you press the Q button, the preset sound setting switches as follows: Scan of Flat – Easy Easy(Default setting) Jazz Flat Rock User memory* Pops Top 40 *User memory: The unit returns to the state adjusted the last time with the audio control setting feature. NOTE The System Q function changes the values of the following sound quality parameters: Bass center frequency, bass level, bass quality factor, bass extend, middle center frequency, middle level, middle quality factor, treble center frequency, treble level, non-fading level, high-pass filter frequency for front output, high-pass filter frequency for rear output, and low-pass filter frequency for non-fading output. Note that some audio control setting Their setting values speaker and woofer setting Speaker & Woofer setting Speaker setting allows the System Q according t...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :