Instructions Kenwood, Modèle KDC-Z939
Fabricant : Kenwood Taille : 1.33 mb Nom Fichier :
Langue d'enseignement:
Aller à la télécharger
Facilité d'utilisation
1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the sound setting switches. Sound setting Display Flat "FLAT" User memory "User Preset" Rock "ROCK" Pops "POPS" Easy "EASY" Top 40 "TOP 40" Jazz "JAZZ" • User memory: The values set on the (page 10). • Each setting value is changed with the (page 10). First, select the speaker type with the Speaker setting. — 9— General features General features Audio Control 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. Adjustment Item Display Range Bass Center "Bass FRQ" 60/70/80/100 or 150 (Hz) Frequency Bass level "Bass" –8 — +8 Bass Q Factor "Bass Q" 1.00/1.25/1.50/2.00 Bass Extend "Bass EXT" ON/OFF Middle Center "Middle FRQ" 0.5/1.0/1.5/2.0 (kHz) Frequency Middle level "Middle" –8 — +8 Middle Q Factor "Middle Q" 1.0/2.0 Treble Center "Treble FRQ" 10.0/12.5/15.0/17.5 (kHz) Frequency Treble level "Treble" –8 — +8 Balance "Balance" Left 15 — Right 15 Fader "Fader" Rear 15 — Front 15 Non-Fading level* "NF Level" –15 — +15 Front High Pass Filter "HPF Front" Through/40/60/80/100/120/ 150/180/220 (Hz) Rear High Pass Filter "HPF Rear" Through/40/60/80/150/180/220 (Hz) Non-Fading "LPF NF" 50/80/120/Through (Hz) Low Pass Filter* Non-Fading Phase* "NF Phase" Normal (0°)/Reverse (180° ) Volume offset "Volume Offset" –8 — ± 0 • According to the Bass Q Factor setting value, the frequencies that can be set in Bass Center Frequency change as shown below. Bass Q Factor Bass Center Frequency 1.00/1.25/1.50 60/70/80/100 2.00 60/70/80/150 • When the bass extend is set to ON, low frequency response is extended by 20%. • Volume offset: Each source's volume can be set as a difference from the basic volume. • *: This mode is available only when (page 18) is ON. 5 Exit Audio Control mode Press the [AUD] button. Speaker & Woofer Setting Speaker setting allows the System Q settings according to the type of speakers. Woofer setting allows for Network configuration type of subwoofers. 1 Enter Standby Press the [SRC] button. Select the "ALL OFF" display. 2 Enter Speaker & Setting mode Press the [Q] button. "Speaker Setting" — 10 — 3 Select the Setting mode 3 Select the Setting mode Each time the button is pressed it switches between Speaker setting mode and Woofer setting mode. 4 Select the Speaker and Woofer type Press the [ 4] or [ . ] button. Each time the button is pressed the setting switches as shown below. In Speaker setting mode Speaker type Display OFF "OFF" For 5 & 4 in. speaker "5/4 inch" For 6 & 6x9 in. speaker "6* 9/6inch" For the OEM speaker "O.E.M." In Woofer setting mode Woofer type Display OFF "Woofer OFF" 12 in. A type "12in type A" 10 in. A type "10in type A" 12 in. B type "12in type B" 10 in. B type "10in type B" 12 in. C type "12in type C" 10 in. C type "10in type C" 8 in. type "8inch" 12 in. D type "12in type D" 10 in. D type "10in type D" 5 Exit Speaker & Woofer Setting mode Press the [Q] button. Switching Display Type Setting the Display type. Press the [DISP] button. Each time the button is pressed the Display type switches as shown below. Display Display mode Picture "Display Type D" Character information display "Display Type A" Character information display Source type icon "Display Type B" Picture Character "Display Type C" information display The display of each part can be changed. - Picture: (page 14) - Character information display: : (page 12) (page 14) — 11 — General features General features Display switching part for "Display Type A" and "Display Type B" When Display Type is set to "Display Type A" or "Display Type B", the displayed contents are changed. "Display Type A" Character information display part a Character information display part b Character information display part c "Display Type B" Character information display part a Character information display part b 1 Select the Display Type Press the [DISP] button. 2 Enter Display Control mode Press the [S.A] button. "Display Control" is displayed. 3 Switch character information display part b Press the [FM] or [AM] button. Switch character information display c (Only when Display Type is "Display Type A") Press the [ 4] or [ . ] button. Each time the button is pressed The Reference for the display explanation. 4 Exit Display Control Press the [S.A] Character information display part c cannot display the same information as character information display part b. In Tuner source Character information d...
Écrivez votre propre critique du dispositif
)
