Instructions Kenwood, Modèle MZ360229EX(LZH-80WM4)
Fabricant : Kenwood Taille : 252.19 kb Nom Fichier :
Langue d'enseignement:
Aller à la télécharger
Facilité d'utilisation
Cleaning the Unit If this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If this unit is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth. ¤ • Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping this unit with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters. Screen brightness during low temperatures When the temperature of the unit falls such as during winter, the liquid crystal panel’s screen will become darker than usual. Normal brightness will return after using the monitor for a while. 2 | English Components names and Functions Open the monitor 1243 Monitor release knob 1 Monitor release knob Unlock the motor. 2 Dome light switch "ON": The light goes on. "DOOR": The light does on/out with the opening/closing of vehicle doors. "OFF": The light goes out. 3 IR transmitter 4 Audio/ Visual input 2 terminal • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) . • The picture input to the Audio/Visual input 2 terminal can be displayed by selecting “AV-IN2” as described in (page 4). 1 Unlock the motor Press the monitor release knob. 2 Open the monitor Press the monitor dawnward. . • Do not press the LCD of the monitor when opening the monitor. The LCD can damage. • When closing the monitor, press its back until it locks. If the monitor is not closed completely, the monitor is held powered. English | 3 Operations POWERINPUT/MENUSCRN/.. DIM/.. POWERINPUTSCRNDIM Power Turns power ON or OFF Press the [POWER] button. Video Source Selection Press the [INPUT] button. Each time the button is pressed, the video source switches as follows: DisplaySetting "AV-IN1" Select the AV1 INPUT source. "AV-IN2" Select the AV2 INPUT source. Display information When you press the [INPUT] button, the status of the monitor is displayed. Mode Full I R 2 MHz AV-IN2 1 3 2 1 Screen mode Display 2 IR headphones output frequency display 3Video source Display . • The information display is cleared automatically after approximately 5 seconds. 4 | English Picture Quality setting You can adjust the picture quality control of the monitor. 1 Enter Picture Quality setting mode Press the [MENU] button for at least 2 seconds. 2 Select the screen for brightness ("BRT") setting Press the [SCRN] or [DIM] button for at least 2 seconds. Pressing the button for at least 2 seconds toggles between the "Day" screen (for daytime brightness setting) and the "Night" screen (for nighttime brightness setting). 3 Select the adjusting item Press the [MENU] button. Each time the button is pressed, the adjusting item switches. Screen.ControlNight 4 Adjust the item Press the [2] or [3] button. Item Button Setting . • The "TIN" can be adjusted when NTSC video signal is input. • The screen select can be set for each source. • If you make no operation for 15 seconds, this mode is automatically canceled. Selection of Screen Brightness Setting You can switch between the daytime screen brightness and nighttime screen brightness adjusted in the Picture Quality setting mode. Press the [DIM] button. Pressing the [DIM] button toggles between the daytime screen brightness and nighttime screen brightness adjusted in the Picture Quality setting mode. "BRT" [3] [2] "TIN" [3] [2] "COL" [3] [2] "CONT" [3] [2] "BLK" [3] [2] Brighter screen Darker screen Stronger red level Stronger green level Deeper color Paler color Stronger contrast Less contrast Less black level Stronger black level 5 Exit Picture Quality setting mode Press the [MENU] button for at least 2 seconds. English | 5 Operations Switching Screen mode Press the [SCRN] button. Each time the button is pressed, the screen mode switches as follows: DisplaySetting "Full" Full picture mode. "Just" Justify picture mode. "Cinema" Cinema picture mode. "Zoom" Zoom picture mode. "Normal" Normal picture mode. IR Headphones frequency setting You can select the IR Headphones frequency you wish. Press the [SCRN] button for at least 2 seconds. Each time the button is pressed for at least 2 seconds, the frequency output switches as follows: DisplaySetting "2 MHz" The output frequency of IR Headphones is set to 2 MHz. "3 MHz" The output frequency of IR Headphones is set to 3 MHz. 6 | English Specifications Specifications subject to change without notice. Monitor Unit Screen size : 8 inches wide Display system : Transparent TN LCD panel Drive system : TFT active matrix system Number of pixels : 336,960 pixels (480 H . 234 V . RGB) Effective pixels : 99.99 % Pixel arrangement : RGB striped arrangement Back lighting : Cold cathode tube IR Transmitter Output : (2MHz) L ch: 2.3 MHz/ R ch: 2.8 MHz : (3MHz) L ch: 3.2 MHz/ R ch: 3.8 MHz Colour system : NTSC/PAL External video input level (RCA jacks) : 1 ± 0.1 Vp-p/ 75 . External audio input level (RCA jacks) : 1 V/ 100 K. Audio output level (RCA jacks) : 1 V...
Écrivez votre propre critique du dispositif
