Évaluations - 5, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
4 Press [c ccccc]/ [d ddddd] to select “AUTO OFFSET (1–7–2)”, then press [OK]. 6 S: Simplex 5 Press [c ccccc]/ [d ddddd] to switch the function ON (default) or OFF. European versions 6 Press [OK] to complete the setting. 144.0 145.6 145.8 146.0 MHz S – S 7 Press [MNU] to exit Menu mode. S: Simplex Note: Automatic Repeater Offset does not function when Reverse is ON. However, pressing[REV]afterAutomatic Repeater Offset has selected an offset (split) status, exchanges the receive and transmit frequencies. 31 6 6 Most of the repeaters in Europe require that a transceiver transmit a 1750 Hz tone. On a TM-D700E, simply pressing Mic [CALL] causes it to transmit a 1750 Hz tone. It is also possible to program [CALL] on the front panel as a button for transmitting a 1750 Hz tone. 1 Press [MNU] to enter Menu mode. 2 Press [c ccccc ]/ [d ddddd ] to select “RADIO (1–)”, then press [OK]. 3 Press [c ccccc ]/ [d ddddd ] to select “REPEATER (1–7–)”, then press [OK]. 4 Press [c ccccc ]/ [d ddddd ] to select “1750 KEY (1–7–3)”, then press [OK]. 5 Press [c ccccc]/ [d ddddd] to select “1750”. 6 Press [OK] to complete the setting. 7 Press [MNU] to exit Menu mode. • “1750” appears in place of “CALL” as the button label. Note: . All market versions allow the above selection in Menu 1–7–3. . All market versions allow any Mic PF key to be assigned the 1750 Hz Tone function {page 62}. . The transceiver continuously transmits a 1750 Hz tone until you release Mic[CALL]or[CALL]. 32 Some repeaters in Europe must receive continuous signals for a certain period of time, following a 1750 Hz tone. This transceiver is also capable of remaining in the transmit mode for 2 seconds after transmitting a 1750 Hz tone. 1 Press [MNU] to enter Menu mode. 2 Press [c ccccc ]/ [d ddddd ] to select “RADIO (1–)”, then press [OK]. 3 Press [c ccccc ]/ [d ddddd ] to select “REPEATER (1–7–)”, then press [OK]. 4 Press [c ccccc ]/ [d ddddd ] to select “TX HOLD (1–7–4)”, then press [OK]. 5 Press [c ccccc]/ [d ddddd] to switch the function ON (or OFF). 6 Press [OK] to complete the setting. 7 Press [MNU] to exit Menu mode. Note: . All market versions allow the above selection in Menu 1–7–4. . While remaining in the transmit mode, the transceiver does not continuously transmit a 1750 Hz tone. REVERSE FUNCTION REVERSE FUNCTION Press [REV] to switch the Reverse function ON (or OFF). • “R” appears when the function is ON. Note: . If pressing[REV] places the transmit frequency outside the allowable range, then pressing Mic[PTT] causes an error beep to sound; transmission is inhibited. . If pressing[REV] places the receive frequency outside the allowable range, an error beep sounds and no reversal occurs. . Automatic Repeater Offset does not function while Reverse is ON. . You cannot switch Reverse ON or OFF while transmitting. 6 Press [REV] (1 s) to switch the function ON. • The ASC indicator appears when the function is ON. • While direct contact is possible, the ASC indicator blinks. REV ON 144.725 MHz145.325 MHz144.725 MHz TX: 144.725 MHz TX: 144.725 MHz RX: 145.325 MHz RX: 145.325 MHz TX: 144.725 MHz TX: 145.325 MHz RX: 145.325 MHz RX: 144.725 MHz AUTOMATIC SIMPLEX CHECK (ASC) While using a repeater, ASC periodically monitors the strength of a signal that you receive directly from the other station. If the station’s signal is strong enough to allow direct contact without a repeater, the ASC indicator on the display begins blinking. • To quit the function, press [REV] . Note: . Pressing Mic[PTT] causes the ASC indicator to quit blinking. . ASC does not function if your transmit and receive frequencies are the same (simplex operation). . ASC does not function while scanning. . Activating ASC while using Reverse switches Reverse OFF. . If you recall a memory channel or the Call channel that contains Reverse ON status, ASC is switched OFF. . ASC causes receive audio to be momentarily intermitted every 3 seconds. 33 TONE FREQ. ID 4 Press [OK] to program the identified frequency in place of the currently set tone frequency. This function scans through all tone frequencies to • The Tone function will be remained ON. You may press identify the incoming tone frequency on a received [TONE] to switch the Tone function OFF. signal. You may use the function to find which tone • Press [ESC] if you do not want to program the identified frequency is required by your local repeater. frequency. 1 Press [TONE] to switch ON the Tone function. • Press [SCAN] while the identified frequency is blinking, • “T” appears when the Tone function is ON. to resume scanning. 2 Press [F], [T.SEL]. • The current tone frequency appears and blinks. 3 Press [SCAN] to activate the Tone Freq. ID. “T SCAN” appears and blinks. 6 • Scan starts when signals are received. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press Mic [UP]/ [DWN]. • To quit the function, press [ESC]. • When the tone frequency is identified, the iden...
Ce manuel est également adapté pour les modèles :Unité - TM-D700E (2.43 mb)