178 x 50 x 176 mm (w/h/d) Approx. 182 x 53 x 161 mm (w/h/d) Approx. 1.2 kg Parts for installation and connections (1 set, except for the power connecting cord) Front panel case (1) Rotary commander RM-X4S Card remote commander RM-X114 BUS cable (supplied with an RCA pin cord) RC-61 (1 m), RC-62 (2 m) CD changer (10 discs) CDX-848X, CDX-646 MD changer (6 discs) MDX-65 Source selector XA-C30 * XR-CA600X/CA600V/CA600 only Note This unit cannot be connected to a digital preamplifier or an equalizer. Design and specifications are subject to change without notice. 26 Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No sound. • Rotate the volume control dial clockwise to adjust the volume. • Cancel the ATT function. • Set the fader control to the centre position for a 2-speaker system. The contents of the memory have been erased. • The RESET button has been pressed. —t Store again into the memory. • The power cord or battery has been disconnected. • The power connecting cord is not connected properly. No beep sound. The beep sound is cancelled (page 18). Indications disappear from/do not appear in the display. • The clock display disappears if you press (OFF) for 2 seconds. —t Press (OFF) again for 2 seconds to display the clock. • Remove the front panel and clean the connectors. See “Cleaning the connectors” (page 24) for details. Stored stations and correct time are erased. The fuse has blown. Makes noise when the ignition key is in the ON, ACC, or OFF position. The leads are not matched correctly with the car’s accessory power connector. No power is being supplied to the unit. • Check the connection. If everything is in order, check the fuse. • The car does not have an ACC position. —tPress (SOURCE) (or insert a cassette) to turn on the unit. The power is continuously supplied to the unit. The car does not have an ACC position. The power aerial does not extend. The power aerial does not have a relay box. Tape playback The sound is distorted. The tape head is contaminated. —t Clean the head with a commercially available dry-tape cleaning cassette. The AMS does not operate correctly. • There is noise in the space between tracks. • A blank space is too short (less than 4 seconds). • A long pause, or a passage of low frequencies or very low sound level is treated as a blank space. Radio reception Preset tuning is not possible. • Store the correct frequency in the memory. • The broadcast signal is too weak. The stations cannot be received. The sound is hampered by noises. • Connect a power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a car’s aerial booster. (Only when your car has built-in FM/MW/ LW aerial in the rear/side glass.) • Check the connection of the car aerial. • The auto aerial will not go up. —t Check the connection of the power aerial control lead. • Check the frequency. Automatic tuning is not possible. • The local seek mode is set to “ON.” —t Set the local seek mode to “OFF” (page 18). • The broadcast signal is too weak. —t Perform manual tuning. The “ST” indication flashes. • Tune in the frequency accurately. • The broadcast signal is too weak. —— Set to the monaural reception mode (page 18)._ A programme broadcast in stereo is heard in monaural. The unit is in monaural reception mode. —t Cancel monaural reception mode (page 18)._ continue to next page t 27 RDS The SEEK starts after a few seconds of listening. The station is non-TP or has weak signal. —tPress (AF) or (TA) repeatedly until “AF-OFF” or “TA-OFF” appears. No traffic announcements. • Activate “TA. ” • The station does not broadcast any traffic announcements despite being TP. —t Tune in another station. PTY displays “.........” • The current station is not an RDS station. • RDS data has not been received. • The station does not specify the programme type._ XR-CA600X/CA600V/CA600 only Error displays CD/MD playback The sound skips. Dirty or defective disc. XR-CA600X/CA600V/CA600 only (when an optional CD/MD unit is connected) Error displays The following indications will flash for about 5 seconds, and an alarm sound will be heard. NO MAG The disc magazine is not inserted in the CD/ MD unit. —t Insert the magazine in the CD/MD unit. NO DISC No disc is inserted in the CD/MD unit. —t Insert discs in the CD/MD unit. ERROR*1 • A CD is dirty or inserted upside down.*2 —t Clean or insert the CD correctly. • An MD does not playback because of some problem.*2 —t Insert another MD. • A CD/MD cannot play because of some problem. —t Insert another CD/MD. BLANK*1 No tracks have been recorded on an MD.*2 —t Play an MD with recorded tracks on it. RESET The CD/MD unit cannot be operated because of some problem. —t Press the RESET button on the unit. NOT REA...

Ce manuel est également adapté pour les modèles :
Unité - XR-CA600 (2.37 mb)
Unité - XR-CA600V (2.37 mb)
Unité - XR-CA600X (2.37 mb)
Unité - XR-L500 (2.37 mb)