Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Garage Door Receiver Red/Black Wire 2. INSTALLATION The following instructions will show you how to install the receiver. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an electrical outlet different from the one already connected to the power cord of the garage door opener to reduce the chance of interference. The further distance between the receiver and the garage door opener, the less interference between 2 devices. Note: The length of the red/black wire is 20ft, so the receiver must be plugged into an electrical outlet that is within 20ft of the wall mounted door control. If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation. Unplug the power cord of your garage door opener before installation to ensure power is not connected. Wall Mounted Door Control Electrical Outlet WARNING Remove power cord of garage door opener before installation. 1 Remove the wall-mounted door control from the wall by removing the screws. Connect the stripped ends of the Red/Black wire to the 2 terminals (2 screws) on the back of the wall mounted door control. (Polarity does not matter.) Red / Black wire Existing wires Note: There should be another pair of wires connected to the 2 terminals already. Do not remove/ disconnect these existing wires. Note: If you see no screws mounting the wall mounted door control, the screws are probably underneath the front cover. Remove the front cover by pressing onto the tabs on top of the cover. Remove front cover first Different wall-mounted door controls 2. INSTALLATION (CONT) 2 Plug in the connector end of the Red/Black wire to the 18R receiver. Note the orientation of the male & female connector. 3 Plug the receiver into an electrical outlet inside the garage. The red light on the receiver should be on after being plugged into an electrical outlet. Existing wires connected to garage door opener. (Do not remove) RECEIVER RED/BLACK WIRE Note: Alternative wiring options are available, the receiver can be connected directly to the opener’s motor. Please contact customer service for further information regarding alternative wiring options. 4 Re-connect the power cord of the Garage Door Opener. 3. PROGRAM A TRANSMITTER TO THE RECEIVER You need to do the programming in order to add a transmitter to the Model 18TN receiver. Button B Button A Button B Button A Learn Button Model 18T4 Button D Button C 2 1 3 4 5 Plug the receiver into an electrical socket. Press and hold the learn button on the left hand side of the receiver. The red LED on the receiver will flash. Press the assigned button of transmitter 18TN (either button A or B) or transmitter 18T4 (either button A, B, C or D) you want to program to the receiver. The receiver red LED will go off indicates the programming is completed. To program a transmitter to control another receiver, repeat process (1) to (4) but pressing another button. 4. TROUBLE SHOOTING Q: Door opener does not react after pressing the button on the transmitter ? A: - Ensure when the button on the transmitter is pressed, the red light on the transmitter comes on. Otherwise, check if the battery is inserted properly. -The appropriate button on the transmitter should be pressed. -If the red light on the receiver flashes when you press the appropriate button on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. -Ensure the wires that are previously connected to the wall mounted door control are not loose. -Ensure the transmitter has been programmed to the receiver. Refer to section 3 for how to program a transmitter to the receiver. 5. REMOVE TRANSMITTER FROM THE RECEIVER 5. REMOVE TRANSMITTER FROM THE RECEIVER You can delete the transmitter from a receiver. 2 1 Unplug the receiver from the electrical socket. Press and hold the learn button on the left hand side of the receiver when plugging the receiver into an electrical socket, the red LED on the receiver will flash rapidly. All the transmitters and keypads are deleted. You can add up to 15 transmitters as you want to control the same receiver. Simply program the transmitters to the receiver. Skylink® offers Keychain Transmitter Model 18T4 and Keyless Entry Transmitter Model 18K to work with your receiver. For more information, please visit our website at or contact us. 6. ADDITIONAL TRANSMITTER 7. CAUTION RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION : DISCONNECT POWER BEFORE SERVICING. Maximum Rating: Input : 120VAC 60Hz 2W 8. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNI...