Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
NOTE: Do not tighten 1/4”-20 flange nuts to opener studs at this time. You will be instructed when to tighten them in the idrive® main installation and owners manual. Remove the temporary orange label holding the antenna wire. Straighten antenna wire and angle it 45 degrees to the right. NOTE: Do not coil the antenna wire. This will reduce the radio signal range. Power Drill 1/8” Drill Bit 7/16” Socket Driver 45 angle Antenna wire Mounting surface (Header) TOP OF DOOR SUPPORT BRACKET 1/4” X 1-1/2” LAG SCREWs 1/4” - 20 FLANGE NUTS Mounting studs Mounting studs Bracket slots support TorqueMaster® bracket spring tube (2) 1/4” - 20 flange nuts TorqueMaster® spring tube “x” 25 Tools Needed: Tools Needed: Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at INSTALLATION Disconnect Cable S-Hook Hole in Right End Bracket NOTE: See idrive® main installation and owners manual for idrive® parts. Attach the loose disconnect cable (located in opener hardware bag) to the opener with the “S” hook. Close both ends of the “S” hook (with pliers) to lock assembly together. Thread the disconnect cable (behind the counterbalance cable) through the hole in the right hand end bracket; remove all slack between opener and right end bracket. Attaching Disconnect Cables Pliers Mounting Disconnect Handle Bracket Pencil Tape measure 1/8” Drill Bit 7/16” Socket Driver Power Drill Hole in Close “S” Hook End Bracket Right Side of End Bracket 6ft NOTE: See idrive® main installation and owners manual for idrive® parts. Mark a location on the right jamb, 6 feet above the floor to mount the disconnect handle bracket. Drill 1/8” pilot holes for the lag screws. Align top of the bracket with the mark. Fasten bracket to the jamb with (2) 1/4” x 1-1/2" lag screws. (2) 1/4” x 1-1/2” Lag Screws Disconnect Handle Bracket 24 25 Tools Needed: 26 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at NOTE: See idrive® main installation and owners manual for idrive® parts. Note : Bring motor to the down position by pulling the disconnect cable, insure opener disconnect teeth are engaged before installing disconnect handle. Start the #6-20 x 1/2" screw into the disconnect handle. Thread the disconnect cable through the top of the disconnect handle bracket and then the disconnect handle. Locate the disconnect handle in full upper position of disconnect handle bracket. Remove all disconnect cable slack between the opener and the top of the disconnect handle bracket. Tighten #6-20 x 1/2" screw into the disconnect handle until snug, and then tighten screw an additional 1 to 1-1/2 turns to secure disconnect cable to the disconnect handle. Trim off excess cable from bottom of the disconnect handle. CAUTION: Pull Cable on ly taut eno ugh to remove the Cable slack. Pulling the Cable more co uld cause Opener to di sconnect from the TorqueMaster® Spring tube. Apply emergency disconnect label next to the mounted bracket. Use mechanical fasteners if adhesive will not adhere. Using the emergency disconnect, pull disconnect handle downwards and place it in the manual door operated position (Use disconnect label for reference). Motor will be rotated 90° from its packaged position. If motor does not pivot 90°, see troubleshooting section in the main installation and owners manual of your idrive® opener Attaching Disconnect Handle Phillips head screwdriver Wire cutters #6-20 x 1/2” Screw Disconnect Handle Bracket Disconnect Cable Handle Manual operated position Upper Position Emergency Disconnect Label Motor operated position 26 Tools Needed: Tools Needed: INSTAllATION FaIluRE TO PlaCE VICE ClaMPs ONTO VERTICal TRaCk CaN allOW DOOR TO RaIsE aND CausE sEVERE OR FaTal INjuRy. Place vice clamps onto both vertical tracks just above the third roller. This is to prevent the garage door from raising while winding counterbalance springs. IMPORTANT: DO NOT usE IMPaCT GuN TO WIND sPRING(s). Securing Door for Spring winding TRaCk VICE ClaMPs aTTaChED TO INNER RaIl OF TRaCk Vice Clamp COuNTERBalaNCE CaBlE sET sCREW CaBlE DRuM locking Pliers Flat Tip screwdriver CaM PEak sTRaIGhT uP Rotate the cable drum until the set screw faces directly away from the header. TorqueMaster® spring tube cam peak should be pointing straight up. Beginning with the right side, loosen the set screw approximately 2 turns, to adjust cable. using locking pliers, pull on the end of the cable to remove all cable slack. Check to ensure the cable is aligned and seated in the first groove of the cable drum. snug the set screw, then tighten an additional 1-1/2 turns. Cut excess cable. Cable Adjustments wARNINg 27 28 PlaCE VICE ClaMPs aBOVE 3RD ROllER Tools Neede...
Ce manuel est également adapté pour les modèles :Portail automatique - TORQUEMASTER 5140 (8.57 mb)