Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Allstar Products Group, Modèle 9931

Fabricant : Allstar Products Group
Taille : 169.36 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after July 1, 1998. For Information: Phone 610-873- 6900 info@allstarcorp. com FAX 610- 873-6953 allstarcorp.com PART #107713 REV C Installation Instructions Garage Door and Gate Operator Radio Controls Models 9921, 9931, 8822, 8832, 8833 Proper installation of your radio controls will assure years of trouble- free operation. READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE STARTING INSTALLATION TRANSMITTERFigure 1A 104385 RECEIVER Figure 1B STEP 1: SET YOUR CODING SWITCHES CAUTION: THE FACTORY PRESET CODE MUST BE CHANGED TO SAFEGUARD AGAINST UNAUTHORIZED OPERATION. A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Receiver, first set your receiver coding switches to your private code setting using the instructions that follow THEN program your Allstar Classic Quik Code transmitter (following the instructions included with the transmitter) to match the receiver. Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. MODEL 9921 AND 8822: The coding switch in these models consists of eight or nine small switches each of which can be placed in two different positions, On or Off. See Fig. 3. Using a small screwdriver, set the coding switches in both the transmitter and receiver identically. (Your private code). FIGURE 3 DO NOT SET ALL SWITCHEs IN THE SAME POSITION. EXAMPLE: NOT ALL RELAY RADIO 3 2 1 24 VOLTS POWER COMMON FIGURE 4 C. Models 9921 or 9931 Single Door Garage 3 2 1 ON or OFF STEP 2: INSTALL YOUR RECEIVER A. The receiver was designed to be installed in a variety of ways depending on the type of operator and the application. If standard hook- up is not desirable or possible, accessories such as three wire adapter sets and tra...

Ce manuel est également adapté pour les modèles :
Portail automatique - 8822 (169.36 kb)
Portail automatique - 9921 (169.36 kb)
Portail automatique - 8832 (169.36 kb)
Portail automatique - 8833 (169.36 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories