Évaluations - , GPA: ( )

Instructions Audiovox, Modèle 50-0300A-002 SERIES

Fabricant : Audiovox
Taille : 584.1 kb
Nom Fichier : ca043f47-5bfb-4bb2-9549-7d2447676c7b.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Razor knife or similar tool 5. 18 GA wire 4'-6' 6. 7mm Hex Socket Bit 7. Test Light 8. Audiovox Series 640/650 Video Module Nov. 8, 1999 INSTALLATION INSTRUCTION # 44-0039A Printed in the U.S.A MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 1 SCREW, 6-32 X 3/4" PPH 6 2 WASHER, 3.5 mm 4 2 3 SCREW, # 8 X 1 1/2" PWH 1 4 SCREW, # 6 X 1/2" PPH 2 5 MOUNTING BRACKET 1 3 6 SPEAKER GRILLE 1 7 CONSOLE 1 4 8 COVER PLATE 1 9 COVER PLATE DECAL 1 INSTALLATION INSTRUCTION # 44-0039A Nov. 8, 1999 Printed in the U.S.A. 2 I. PREPARATION OF VEHICLE INTERIOR FIGURE 1 1. Using the rear edge of O.E. sunroof opening as a reference location, carefully measure & trim headliner as shown. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Make sure that the 7" cut is centered left to right in vehicle. See Figure 1. DO NOT OVERCUT HEADLINER. 2. Remove and retain lens from middle O.E. dome light. 3. Remove and retain (3) three screws which secure middle O.E. dome light. See Figure 2. FIGURE 3 4. 5. 6. FIGURE 2 Construct a jumper harness that will connect the vehicle’s dome light wires to the lights in video system. Connect the white wire from video system to the O.E. black/blue wire. Connect the black wire from video system to the chassis ground. See Figure 3. Using a test light, test function of lights. Install O.E. dome light in original manner. 3 7. Remove and retain (2) two O.E. screws from bracket. See Figure 4. 8. Carefully pull back edge molding from rear of sunroof opening. See Figure 4. FIGURE 4 9. Insert mounting bracket (item 5 pg. 2) into headliner. Slide bracket forward between headliner and roof until tab engages O.E. roof panel. Align hole in bracket with center rivet on roof panel. See Figure 5. 10. Secure rear of bracket using (2) two O.E. screws, previously removed. 11. Slide edge molding back into original position around sunroof opening. FIGURE 5 4 12. Install and route all video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above the headliner from video system to C-pillar. Down the C- pillar to the floor. Route the power lead to an accessory controlled source. Connect the ground lead to the vehicle chassis. Route the remaining wiring (RCA plugs, Remote Sensor extension, etc.) to the VCP location. See Figure 6. Connect per instructions included with the video system. If video system if to be used as a television, insta...