Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Razor knife or similar 5. 18 GA wire 4' - 6' 6. 1/4" Hex Socket Bit 7. Test light 8. Audiovox Series 640/650 Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF. NOT FOR USE IN VEHICLES EQUIPPED WITH FACTORY REAR A/C. Nov. 8, 1999 INSTALLATION INSTRUCTION # 44-0044A Printed in the U.S.A MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 1 SCREW, # 10 X 1/2" HWH 2 2 SCREW, 6-32 X 3/4" PPH 6 3 WASHER, 3.5 mm 4 2 4 SCREW, # 8 X 1 1/2" PWH 1 5 SCREW, # 6 X 1/2" PFH 2 3 6 MOUNTING BRACKET 1 7 SPEAKER GRILLE 1 4 8 CONSOLE 1 9 COVER PLATE 1 10 COVER PLATE DECAL 1 5 INSTALLATION INSTRUCTION # 44-0044A Nov. 8, 1999 Printed in the U.S.A. 2 I. PREPARATION OF VEHICLE INTERIOR FIGURE 1 1. Remove and retain O.E. dome light by gently prying downward on rear edge of lens then slide frame assembly out. Disconnect wiring and lay dome light in a safe place. See Fig. 1. 2. Using the front edge of dome light opening as a reference location, carefully measure & trim headliner as shown. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Make sure that the 7" cut is centered left to right in vehicle. See Figure 2. DO NOT OVERCUT HEADLINER. 3. Scribe a center line on the sheet metal roof of the vehicle in front and rear of openings in headliner. This will be used for bracket alignment. See Figure 2. FIGURE 2 FIGURE 3 4. Install mounting bracket (item 6 pg. 2) with the bent edges upward. Slide bracket rearward until rear tabs engage rear O.E. roof brace. Align notches in bracket with center lines scribed on roof. See Fig. 3 and Fig. 4. 5. Secure front of bracket to front roof brace using (2) two # 10 X 1/2" screws (item 1 pg 2). 3 6. Make sure tabs on mounting bracket engage O.E. roof brace and notch aligns with center line. See Figure 4. FIGURE 4 7. Construct a jumper harness that will connect the vehicle’s dome light wires to the lights in video system. Connect the white wire to the O.E. pink wire. Connect the black wire to the O.E. yellow wire. See Figure 5. 8. Using a test light, test function of lights. 9. Install O.E. dome light in original manner. FIGURE 5 4 10. Install and route all video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above the headliner from video system to B-pillar. Down the B-pillar to the floor. Route the power lead to an accessory controlled source. Connect the ground lead to the vehicle chassis. Route the rema...
Ce manuel est également adapté pour les modèles :Vidéo de voiture - 650 (546.69 kb)