Log:
Évaluations - 6, GPA: 4 ( )

Instructions Audiovox, Modèle 50-0244x-001 SERIES

Fabricant : Audiovox
Taille : 750.64 kb
Nom Fichier : b63c9449-4c3b-41aa-95cd-472b0a29a2cc.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


2 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. console mounted to inner roof of vehicle. Remove and discard dome light cover to gain access to (2) two #8 x 3/4" screws. Retain screws. Remove and retain (1) one #8 x 1 1/2" screw located in front of console near rear view mirror. See Figure 1. 2. Lower console and disconnect wiring at (2) two locations. Lay console on workbench for modification later. See Figure 2. 3. Using rear edge of opening in headliner, carefully trim headliner as shown and install mounting bracket (item 5 pg 2). Make sure the 8” cut is centered in vehicle. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Secure front of bracket to roof brace using (2) two O.E.M. screws, previously removed, in original locations. Make sure that bracket is centered in vehicle and secure rear of bracket to roof brace using (4) four #8 x 3/4" screws (item 1 pg 2). Install (2) two #8 x 3/4" screws (item 1 pg 2) in remaining holes next to O.E.M. screws previously installed. See Figure 3. FIGURE 1 FIGURE 2 FIGURE 3 3 II. PREPARATION OF CONSOLE FOR INSTALLATION 4. Turn console upside down and remove and retain (15) fifteen T-15 TORX screws which secure the cloth covered trim ring to console. See Figure 4. FIGURE 5 FIGURE 4 5. Turn console over and open both compartment doors. Carefully separate the console from trim ring. Remove electronic compass from console and lay it in a safe place for use later. Remove and retain velcro tape and lay it in a safe place for later use. Discard cloth covered trim ring. See Figure 5. 6. Cut the orange and black wires from dome light. Cut all wires 7” from tape where indicated. See Figure 6. FIGURE 6 4 FIGURE 7 7. Mark a line on both sides of dome light as close to the edge as possible. Using a band saw or suitable tool, carefully trim console as shown. Discard dome light. Note: If console is trimmed too far away from dome light, the trimmed edge may be visible when installed in vinyl console. See Figure 7. Installer’s option: Turn console over and place on a padded surface. Trim console along ridge on either side of dome light. 8. Install the electronic compass in original position and secure using (2) two pieces of felt tape (item 7 pg 2). See Figure 8. FIGURE 8 5 FIGURE 9 9. Carefully insert modified console into vinyl covered console as shown. Insert the video system in the opening in center of console. See Figure 9. Note: Leave compartment door open to the 90 degree position until console is installed in vehicle. This will allow access for installing screws. If the door is closed prior to installation in vehicle, it will not open enough to properly install screws. CAUTION: The edges of O.E.M. console may be sharp and could cut the vinyl console during installation. It may be necessary to deburr the edge of console before installation. 10. Carefully turn console over and secure O.E.M. console using original screws. Start all sc...

Ce manuel est également adapté pour les modèles :
Vidéo de voiture - 50-0244x-018 SERIES (750.64 kb)
Vidéo de voiture - 50-0244x-019 SERIES (750.64 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories