Évaluations - , GPA: ( )

Instructions Audiovox, Modèle DVD PLAYER VOD1023

Fabricant : Audiovox
Taille : 149.4 kb
Nom Fichier : vod1023x.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Important Notice An LCD panel and/or video monitor may be installed in a motor vehicleand visible to the driver if the LCD panel or video monitor is used forvehicle information, system control, rear or side observation ornavigation. If the LCD panel or video monitor is used for televisionreception, video or DVD play, the LCD panel or video monitor must beinstalled so that these features will only function when the vehicle is in“park” or when the vehicle’s parking brake is applied. An LCD panel or video monitor used for television reception, video orDVD play that operates when the vehicle is in gear or when the parkingbrake is not applied must be installed to the rear of the driver’s seatwhere it will not be visible, directly or indirectly, to the operator of themotor vehicle. Important Note This DVD player incorporates two new features: 1) A wireless FM Modulator 2) Capability to add an optional plug in TV tuner (Audiovox P/NPODTVT – must be ordered separately) Please be advised that the wireless modulator will perform well inmost applications. However, in certain applications the quality ofthe wireless signal may be less than optimal, resulting in static orstrong local station bleed thru. If this is the case, an optional relaybox is available. The Audiovox part number is SIRSWB and plugsinto the 1/8" jack on the side of the chassis. This relay box isinstalled between the vehicle antenna and the car radio to providethe best possible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the3.5mm jack be unplugged. See page 6 of this manual for additional information. MATERIALS INCLUDED IN THIS PACKAGE: 1) VOD1023 TV/Video Monitor with DVD (1pc) 2) 12 Pin Power / Signal harness (P/N 112-3483) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/ N 112B3143) (1 pc) 4) Hardware Package #4 x 3/8” Screws (9 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 5) Remote Control (1363855) (1pc) 6) PODTVT TV Tuner (P/N 136-3877) (1pc) (Optional) 7) SIRSWB Relay Box (P/N 112C3159) (1pc) (Optional)-See important note on previous page 8) Trim Ring (1pc) 9) Game Controller (P/N 136-3982) (1pc) -1- TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle) DVD Movie (to verify system operation after installation) 1 2 3 4 5 6 IRTA ON /O FF ON /O FF IRTB 7 8 (Optional) (Optional) SOURCE 9 GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim components etc.), this should be done now as well. (Refer to Page 3). 5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on pages 6 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 6) Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 7) Connect all components together (electrically) and verify proper operation of all system functions. Note: This is best done BEFORE, components have been permanently mounted. 8) After verifying proper operation of the system, proceed to mount of each component. 9) When all components are mounted, recheck function of entire system again to ensure that no wiring was pinched or connected improperly during final installation. GENERAL SYSTEM CONFIGURATIONS: The following is intended to provide some of the system configurations that are possible with the VOD1023 series Drop Down Video Systems: Notes : There are a few audio output options that can be added as follows: a) Wireless Headphones (P/N MVIRHS). b) Wired relay box for wireless FM Modulator (P/N SIRSWB). The VOD1023 video systems are only intended for an overhead, drop down installation. It is not intended ...