|
Facilité d'utilisation
Warning notice: The operating voltage cable must be protected with at least a 1.5 A fuse. Monitor connection (13 pin) Connect the system cable (13 pin) > to a signal controller (IVSC-3302 or IVSC-5502). (The voltage supply is provided by these devices. Operating instructions are supplied with the devices). Or Use the plug-in adapter cable ? to connect to the 12 V supply voltage and an external video/DVD device: Red = +12 V direct current Black = Earth Red RCA = Audio IN (R) White RCA = Audio IN (L) Yellow RCA = Video IN Jack plug (blue) = Do not use! (Only for special devices) 23 OPERATION Controlling the interior lighting (monitor) There are two switches for the lights: ON 2 and interior lighting 4. ON : This button is used to switch the lights on/off. Interior lighting : If activated, the lights only come on when the vehicle’s doors are opened. 24 Opening the monitor . Pull back the monitor release latch 3 to flip down the LCD display. . To watch television, lower the monitor until it is at an angle of approx. 90° to the monitor’s base unit. 3 OPERATION Adjusting the position of the monitor The monitor can be rotated by up to approx. 30°to the right and left from its central viewing position. Closing the monitor . Turn the monitor back to its central viewing position and push it into its base unit so that it clips back into the releasing/locking mechanism. Switching on the monitor Press the power-on button 9on the main unit or the button Don the re- mote control to switch the monitor on/ off. Note: The button 9lights up blue before the DHEFGIJ 9;78: OPERATION Adjusting the position of the monitor The monitor can be rotated by up to approx. 30°to the right and left from its central viewing position. Closing the monitor . Turn the monitor back to its central viewing position and push it into its base unit so that it clips back into the releasing/locking mechanism. Switching on the monitor Press the power-on button 9on the main unit or the button Don the re- mote control to switch the monitor on/ off. Note: The button 9lights up blue before the DHEFGIJ 9;78: monitor is switched on. This means that the monitor is connected to the 12 V voltage supply. ENGLISH 25 OPERATION OSD menu Operation . Press the MENU button : on the display or the MENU button I on the remote control to open the OSD menu. . Use the arrow buttons 7 / 8 or I / to select the options. After you press the MENU button : or I you can use the arrow buttons to change the settings. . Select the “EXIT” option to close the OSD menu again. SPEAKER ON ZOOM BRIGHTNESS CONTRAST COLOR TINT REVOLVE LEFT-RIGHT UP-DOWN RESET PICTURE EXIT . SPEAKER ON Switch the internal loudspeaker on/ off (same function as the MUTE button G on the remote control). The sound then continues to be outputted over the IR headphones IVHS-01 (accessory). . ZOOM (picture size) only IVMR-9002: Change the picture height/width -FULL -NORMAL -WIDE . BRIGHTNESS: To adjust the brightness . CONTRAST: To adjust the contrast . COLOR: To adjust the colour . TINT: To adjust the picture shade (only for NTSC) . REVOLVE: To revolve the screen display - LEFT - RIGHT: Mirror horizontally -UP - DOWN: Mirror vertically . RESET PICTURE: To reset the configured parameters to the factory default settings. . EXIT: To close the OSD menu IR headphones IVHS-01 (accessory) The IR transmitter window 6 must not be covered up when using the IR headphones IVHS-01 (accessory). OPERATION Changing the light bulb . Detach the monitor from the ceiling plate (4 screws). Screws for securing the ceiling-mounted monitor . Remove the 3 screws of the metal cover (see picture below). . Take out the old bulb. . Fit a new bulb (12 V, 3 W). . Refit the monitor. Light bulb specifications Diameter: 8 mm Length: 28 mm Voltage: 12 V, 3 W Changing the battery in the remote control . Push the button on the battery compartment J to the right (see A below). . Pull the battery compartment J out of the remote control (see B below). . Change the 3 V battery (CR 2025). AB J ENGLISH Metal cover Bulb 27 SPECIFICATIONS IVMR-9002 Screen size: 9" Monitor Screen resolution: 1440 (H) x 234 (V) Active area: 198.0 (H) x 111.74 (V) Signal system: Dual system NTSC/PAL Brightness: 300 cd/m2 Contrast ratio: 100 Viewing angle: Left/right: 65/65 degrees Up/down: 50/65 degrees Video input level: 1.0 Vpp ± 10 % Audio input level: 0.3 Vrms AUX input level: 1.0 Vpp ± 10 % Carrier frequency for IR sensor: L-CH: 2.3 MHz R-CH: 2.8 MHz Operating voltage (direct current): 10-16V Current consumption: 1 A (at +12V) Quiescent current consumption: 35 mA (at +12 V) Operating temperature: 0 - 60 °C Storage temperature: - 30°C to +80°C Dimensions: 286 x 258 x 57.4 mm Weight: . 2150 g Subject to changes! SPECIFICATIONS IVMR-1042 Screen size: 10.4" Monitor Screen resolution: 1920 (H) x 480 (V) Active area: 211.2 (H) x 158.4 (V) Signal system: Dual system NTSC/PAL Brightness: 290 cd/m2 Contrast ratio: 100 Viewing angle: Left/right: 60/60 degrees Up/down: 40/50 degrees V...
Ce manuel est également adapté pour les modèles :Vidéo de voiture - IVMR-9002 (430.88 kb)