Fabricant : Panasonic Taille : 2.16 mb Nom Fichier : Langue d'enseignement:

Aller à la télécharger

Programming using the direct commands 1 {MENU} i {#} 2 Enter the desired feature code. 3 {V}/{^}: Select the desired setting. i {SAVE} L This step may vary depending on the feature being programmed. L To exit the operation, press {¦}(EXIT) on the base unit or {OFF} on the handset. Note: L The operating unit column shows the unit(s) that can be used to program the item. =: Only the base unit can program the item. Y: Only the handset can program the item. =/Y: Both the base unit and handset can program the item. L In the following table, < > indicates the default settings. Operating unit Feature Feature code Setting System setting*1 Page Y Alarm {7}{2}{0} Once Daily – 25 Y Answer off {3}{2}{8} – r 31 Y Answer on {3}{2}{7} – r 31 Y Auto talk*2 {2}{0}{0} On – 14 =/Y Block w/o num. (Block calls without phone number) {2}{4}{0} On r 26 =/Y Call block {2}{1}{7} – r 26 =/Y Caller ID edit (Caller ID number auto edit) {2}{1}{4} Off – 29 =/Y Caller list {2}{1}{3} – – 28 Y Check greeting {3}{0}{3} – – 32 =/Y Customer support*3 {6}{8}{0} – – – Y Date and time {1}{0}{1} – r 12 Y Deregistration {1}{3}{1} – – 27 = Display language {1}{1}{0} Espanol – 12 Y Display(Change language) Y Erase all msg. (msg.: messages) {3}{2}{5} – r 33 Y Intercom {2}{7}{4} – – 38 Y Key tone*4 {1}{6}{5} Off – – =/Y LCD contrast (Display contrast) {1}{4}{5} Level 1–6 <3> – – For assistance, please visit Programming Operating unit Feature Feature code Setting System setting*1 Page Y Message alert {3}{4}{0} On – 36 Y Play all msg. (msg.: messages) {3}{2}{4} – – 33 Y Play new msg. (msg.: messages) {3}{2}{3} – – 33 Y Pre-recorded (Reset to pre-recorded greeting) {3}{0}{4} – r 32 Y Record greeting {3}{0}{2} – r 31 Y Recording time {3}{0}{5} 1min <3min> Greeting only r 35 Y Register handset {1}{3}{0} – – 27 Y Remote code {3}{0}{6} <111> r 34 Y Ring count {2}{1}{1} Toll saver 2–7 rings <4> r 35 =/Y Ringer tone*5, *6 {1}{6}{1} Base unit: Tone <1>–6 Handset*7: Tone <1>–5 Melody 1–10 – – =/Y Ringer volume*8 {1}{6}{0} Base unit: Level 1–<3>, Off Handset: Level 1–<6>, Off – 14 =/Y Screen call {3}{1}{0} Off – 31 Y Set dial mode {1}{2}{0} Pulse r 12 Y Set flash time*9 {1}{2}{1} 80ms 90ms 100ms 110ms 160ms 200ms 250ms 300ms 400ms 600ms <700ms> 900ms r 15 Y Set line mode*10 {1}{2}{2} A r – =/Y Silent mode (On/Off) {2}{3}{8} On – 25 =/Y Silent mode (Start/End) {2}{3}{7} <11:00 PM/06:00 AM> – 25 Y Time adjust*11 (Caller ID subscribers only) {2}{2}{6} Manual r – For assistance, please visit Programming Operating unit Feature Feature code Setting System setting*1 Page Y VM tone detect (VM: Voice mail) {3}{3}{2} Off r 37 Y Voice prompt(Change language) {1}{1}{2} Espanol r 12 *1 If “System setting” column is checked, you do not need to program the same item using another unit. *2 If you subscribe to a Caller ID service and want to view the caller’s information after lifting up the handset to answer a call, turn off this feature. *3 The base unit and handset can display the Internet address where you can download the operating instructions or get further information for this product, using your computer. *4 Turn this feature off if you prefer not to hear key tones while you are dialing or pressing any keys, including confirmation tones and error tones. *5 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (base unit: tone 1 to 6/handset: tone 1 to 5). If you select a melody, you cannot distinguish lines by their ringers. *6 If you select one of the melody ringer tones, the ringer tone continues to play for several seconds even if the caller has already hung up. You may either hear a dial tone or no one on the line when you answer the call. *7 The preset tones and melodies in this product are used with permission of © 2007 Copyrights Vision Inc. *8 When the ringer volume is turned off, ~ is displayed and the base unit and/or handset do not ring for outside calls. However even when the ringer volume is set to off: – the base unit rings at the low level for intercom calls (page 38). – the handset rings at the lowest level for alarm (page 25) and intercom calls (page 38), and rings at the highest level for paging (page 38). *9 The flash time depends on your telephone exchange or host PBX. Contact your PBX supplier if necessary. The setting should stay at “700ms” unless pressing {FLASH} fails to pick up the waiting call. *10Generally, the line mode setting should not be adjusted. If “New Voice Mail” is not displayed, even when the message indication service is available (page 37), you need to change the line mode to “A”. *11This feature allows the unit to automatically adjust the date and time setting when caller information is received. To use this feature, set the date and time first. For assistance, please visit Programming Special programming Silent mode ...

Ce manuel est également adapté pour les modèles :
Auto intervenants - KX-TG1063 (2.16 mb)
Auto intervenants - KX-TG1061 (2.16 mb)

Téléchargez votre

Pour télécharger, entrez 2 chiffres :